My Orders
KB26G1XER5 KitchenAid Mixer - Overview
Diagrams for KB26G1XER5
See every part. Know exactly what you need.
Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".
Search filter:
Clear Filter
Your search term must have 3 or more characters.
$34.27
In Stock
$40.95
In Stock
Hub Gear
Part #W11192795
Includes both the attachment and beveled gear. This worm follower gear is for stand mixers.
Worm follower gear meshes with the worm gear, causing the rotation of the planetary assembly where the accessories attached.
Unplug the mixer before installing this part. Wear work gloves to protect your hands.
$73.14
In Stock
Mixer Worm Gear
Part #WP9709231
Keep your stand mixer running smoothly with this replacement worm gear, which powers the planetary assembly where beaters and other attachments connect. Made from high-quality metal, it’s built to withstand regular use. Common signs of a failing gear include the mixer not starting, inconsistent mixing, or strange grinding sounds. This par...Read moret is compatible with select models and is a reliable fix for restoring performance.
Read less
$12.00
In Stock
Dryer Retaining Ring
Part #WP9703438
This metallic retaining ring is less than an inch in diameter. It is made entirely of metal.
$13.15
In Stock
$111.90
In Stock
Stand Mixer Gear Grease
Part #W11200218
This Stand Mixer Gear Grease lubricates the moving parts of the stand mixer.
$18.09
In Stock
$13.12
In Stock
$21.90
In Stock
Mixer Thrust Bearing Kit
Part #WP9703445
This bearing comes equipped with two washers and is used on stand mixers.
$142.97
In Stock
Stand Mixer Speed Control Board and Knob (Black)
Part #WP9706648
If your stand mixer isn’t adjusting speeds like it used to, this speed control switch might be the fix. It comes with the black knob and lets you fine-tune how fast your mixer runs—perfect for everything from slow stirring to fast whipping. It’s a genuine part made for KitchenAid and Whirlpool mixers, so you know it’ll fit right. Just make sure to unplug your mixer before swapping it out!
$13.14
In Stock
Mixer Retaining Pin
Part #WP9707223
This small metal pin locks the center gear to its shaft inside a stand mixer. Replace it if the pin is bent, broken, or missing. A damaged pin may let the motor run while the beater stays still. This is an internal gear pin, not the large hinge pin that joins the mixer head to the base. Use the full mixer model number to guarantee the proper fit. Unplug the mixer before opening the gear housing.
$37.53
In Stock
Mixer Thumb Screw
Part #WP9709194
This part is used with the stand mixers attachments, as well as to hold the end cap to the front of the mixer.
Manuals & Care Guides for KB26G1XER5
Click to downloadCommon Symptoms of the KB26G1XER5
How this model fails, and the parts that fix it.
Noisy
Fixed by
these parts
these parts
Show All
Touchpad does not respond
Fixed by
these parts
these parts
Show All
Leaking
Fixed by
these parts
these parts
Show All
Grinding or squealing sound
Fixed by
these parts
these parts
Show All
Watch our pros, then fix it yourself.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!
View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Plastic gear housing in stand mixer fractured causing gears to crash
70 of 107 people
found this instruction helpful.
Removed four screws to remove main cover. Removed four more screws to remove fractured plastic gear housing cover. Removed retainer ring and slid two gears and dowel off main shaft. Lifted out remaining gear train and bearings, Removed all grease and metal chips from all components. Greased new gears and reassembled. Replaced plasti
... Read more
c gear housing cover with oreviously purchased die cast replacement part. Assembled main cover.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Mixer Made Very Bad Grinding Noise, And Would Skip While Making Bread Dough
79 of 94 people
found this instruction helpful.
1, Removed trim piece (1 screw) 2, removed cover (4 screws) 3, removed speed switch assembly (2 screws) 4, removed gear cover (4 screws) 5, removed and examined 2 worm gears for wear. Gear cover was badly cracked, don"t know if it was caused by a previous repair or by heat, as old cover is plastic. Received new parts and installed them
... Read more
, 2 bearings, 2 worm gears, 1 new cover of diecast metal and a new gasket. All repairs made with a #2 phillips screw driver. My wife then made bread, and it preformed flawlessly.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!