This is the replacement charcoal filter for your microwave. It is silver and black in color and measures approximately 10 inches by 2 ½ inches. The charcoal filter removes cooking odors from the air ...
This is a genuine replacement 40 watt bulb for a microwave. The bulb is meant to light up the underside of the microwave or inside of your microwave when the door is open or during use. If your bulb i...
This turntable motor is for microwaves.
The turntable motor rotates the glass tray inside the microwave oven.
Because high-voltage capacitors in a microwave can retain a lethal electrical charge...
Ask our experts a question about this model and we'll get back to you as soon as possible!
6 questions answered by our experts.
< Prev
1
2
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Scott
July 27, 2021
Can you just buy the handle and not a complete door?Thanks,
scott
For model number JVM3160DF4CC
Hello Scott, Thank you for your inquiry. You can purchase the handle separately for this model, the part number is PS8754174. Hope this helps.
4 people found this helpful.
Was this helpful?
Thank you for voting!
Laura
September 1, 2021
The circuit breaker keeps flipping.
For model number JVM3160DF4CC
Hello Laura, Thank you for the question. This is normally an indication one or more of the Door Switches are defective and causing a power surge that trips the breaker. You can test each switch with a multi meter to check the continuity. We hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Robby
January 26, 2020
How do I install a charcoal filter on new unit?
For model number JVM3160DF4CC
Hi Robby,
Thank you for your question. To replace/install a charcoal filter, open the microwave door and then push the press and release access door that is located across the top of the oven. Then remove and replace the charcoal filter. Close the access door and then close the microwave door. We hope this helps. Thank you and have a great day.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Robert
February 25, 2020
When you try to push any button on the main panel it blows the breaker.
For model number JVM3160DF4CC
Hello Robert, thank you for your question. We would recommend testing the thermostats, fuse and door switches in the unit. If those parts are ok, the issue would be most likely with the main control board in the unit. I hope this helps.
Was this helpful?
Thank you for voting!
Alice
November 3, 2022
The digits on the clock are partially displayed. Is there a replacement part available to fix this?
For model number JVM3160DF4CC
Hello Alice, thank you for your query. According to our research, the electronic control board, part number PS11762558, needs to be replaced. Additionally, you can also check the microwave interface, part number PS8753703, to resolve your problem. We look forward to hearing from you if you need assistance with placing an order through our 7-days-a-week customer service. We hope this helps!
Was this helpful?
Thank you for voting!
< Prev
1
2
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
Open the front cover by pushing it at the top (where it says “Push”), lifting up and pushing back on top edge of the old filter. Pull it out. Installing the new one is basically just the reverse of those steps! That simple.
Old filter did seem to be a little thicker (filter material), but the new one was the exact same dimensions, so it went in properly. Wish the filter material was white, so you knew just how dirty it was actually getting. But... :-D
1. Unplug unit 2. Open door, remove two screws above the top trim piece, slide and remove trim. 3. Remove screw behind control board and top left corner, then release from position. 3b. Unplug all wire terminations and set control panel aside. 4. Remove two screws securing latch board, lift and rotate board out of position, remove three micro switches, xfer monitor switch actuator from lower pin in old board and insert in new. Install new door switches and reverse procedure to complete repair.
Note 1. Take care to located new latch board so holding tabs line up, pass through frame, and openings for door tangs line up with openings in frame before securing with screws.