This is the replacement charcoal filter for your microwave. It is silver and black in color and measures approximately 10 inches by 2 ½ inches. The charcoal filter removes cooking odors from the air ...
This is a genuine replacement 40 watt bulb for a microwave. The bulb is meant to light up the underside of the microwave or inside of your microwave when the door is open or during use. If your bulb i...
This turntable motor is for microwaves.
The turntable motor rotates the glass tray inside the microwave oven.
Because high-voltage capacitors in a microwave can retain a lethal electrical charge...
Ask our experts a question about this model and we'll get back to you as soon as possible!
5 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Richard
August 10, 2023
The fan has lost power to move the smoke into vents instead of the room.
Sets off smoke alarms.
For model number JVM3160DF2CC
Hi Richard, thank you for your inquiry. A buildup of grease, food particles, or other debris inside the microwave can impede the airflow and cause smoke to accumulate. Regularly clean the interior of the microwave, the turntable, and the filters or screens. Ensure that the vents or ducts leading from the microwave to the outside are clear and not blocked by any obstructions. This will allow the exhaust fan to expel smoke effectively. If all checks are fine, we recommend replacing the fan motor, part number PS8754500. We hope this information is useful!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Perry
November 30, 2019
Microwave does not operate, no power at keypad. Tested 120v at outlet and plug in completely.
For model number JVM3160DF2CC
Hi Perry, I would check the fuse. Thank you for your question and good luck with your repair!
Was this helpful?
Thank you for voting!
Clayton
March 14, 2020
Everything works exself want heat wart or cook food
For model number JVM3160DF2CC
Hello Clayton, thank you for your question. That issue is usually caused by a faulty, diode, door switch, capacitor or magentron. We would recommend testing those parts first. I hope this helps.
Was this helpful?
Thank you for voting!
Jim
July 23, 2021
Everthing stopped working
For model number JVM3160DF2CC
Hi Jim,
Thank you for your question. If your microwave will not turn on, there are some parts that you will need to check to see which one is causing the issue. You will need to check the microwave fan thermostat, the microwave fuse, the thermostat, the door switches, the light socket and the door latch. We hope this helps! Good luck with the repair!
Was this helpful?
Thank you for voting!
Donna
March 20, 2022
What is the height of this unit.
For model number JVM3160DF2CC
Hello Donna, thank you for writing. The Dimensions: 16 1/8 H x 29 7/8 W x 15 9/16 D. We hope this helps.
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
Open the front cover by pushing it at the top (where it says “Push”), lifting up and pushing back on top edge of the old filter. Pull it out. Installing the new one is basically just the reverse of those steps! That simple.
Old filter did seem to be a little thicker (filter material), but the new one was the exact same dimensions, so it went in properly. Wish the filter material was white, so you knew just how dirty it was actually getting. But... :-D
1. Unplug unit 2. Open door, remove two screws above the top trim piece, slide and remove trim. 3. Remove screw behind control board and top left corner, then release from position. 3b. Unplug all wire terminations and set control panel aside. 4. Remove two screws securing latch board, lift and rotate board out of position, remove three micro switches, xfer monitor switch actuator from lower pin in old board and insert in new. Install new door switches and reverse procedure to complete repair.
Note 1. Take care to located new latch board so holding tabs line up, pass through frame, and openings for door tangs line up with openings in frame before securing with screws.