Models > JVB67A3CC

JVB67A3CC General Electric Range Hood - Overview

Sections of the JVB67A3CC

[Viewing 1 of 1]
RANGE HOOD Diagram and Parts List for General Electric Range Hood
RANGE HOOD
Keep searches simple, eg. "belt" or "pump".
Single Roller – Part Number: WC2X5144
Single Roller
PartSelect #: PS257711
Manufacturer #: WC2X5144
Sold individually.
  No Longer Available
Hood Gear Motor – Part Number: WB26X10050
Hood Gear Motor
PartSelect #: PS237784
Manufacturer #: WB26X10050
  No Longer Available
REMOTE TRIM BASE – Part Number: WB07X10181
REMOTE TRIM BASE
PartSelect #: PS229330
Manufacturer #: WB07X10181
$28.83
  Special Order
SEAL – Part Number: WB02X10309
SEAL
PartSelect #: PS223618
Manufacturer #: WB02X10309
$50.46
  Special Order
Air Filter – Part Number: WB02X10310
Air Filter
PartSelect #: PS223619
Manufacturer #: WB02X10310
$56.47
  Special Order
KNOB – Part Number: WB03X10005
KNOB
PartSelect #: PS226730
Manufacturer #: WB03X10005
  No Longer Available
HEYCO BUSHING – Part Number: WB01X10006
HEYCO BUSHING
PartSelect #: PS222353
Manufacturer #: WB01X10006
$4.66
  Special Order
FORMED BOX – Part Number: WB02X10301
FORMED BOX
PartSelect #: PS223610
Manufacturer #: WB02X10301
$61.44
  Special Order
SLIDE – Part Number: WB07X10012
SLIDE
PartSelect #: PS229165
Manufacturer #: WB07X10012
  No Longer Available
SWITCH VARIABLE SPEED – Part Number: WB24X10035
SWITCH VARIABLE SPEED
PartSelect #: PS237003
Manufacturer #: WB24X10035
  No Longer Available
Remote Trim Kit - Bisque – Part Number: WB07X10686
Remote Trim Kit - Bisque
PartSelect #: PS952578
Manufacturer #: WB07X10686
  No Longer Available
TRIM SWITCH EMBOSSED – Part Number: WB07X10216
TRIM SWITCH EMBOSSED
PartSelect #: PS229364
Manufacturer #: WB07X10216
  No Longer Available
Back to Top
View More

Questions And Answers for JVB67A3CC

Be the first to ask our experts a question about this model!

Back to Top

Common Symptoms of the JVB67A3CC

[Viewing 1 of 1]
Drawer is hard to open and or close
Fixed by
these parts
Fixing
Show All
Back to Top
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Controller board fried
Disconnected power and removed electrical cover
Disconnected wires from old controller one a time and connected to new controller as to not mismatch wire connections. Left new controller hanging off wires.
Raised vent and held using wood blocks to expose gap to use 1/4 inch wrench to undo screws from the inside (poor design for replacing the controller - this was the bulk of my time.) if this didn't work, I would have had to disassemble more of the downdraft.
Installed new controller.
Removed chocks, enabled power and tested...after verified, re-installed electrical cover.
Parts Used:
Control Board
  • Anthony from Stevensville, MD
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Wrench set
6 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Back to Top
View More