JGP336WED2WW General Electric Cooktop - Instructions

Assumed the entire top of the range would have to be lifted off. Removed the three screws inside the top of the over door and then noticed the two screws holding the dish around the burner. They were tight and required WD-40 and then a sharp tap and came off.
Important: Notice the direction your old igniter is plugged into the wire. It is not clear and can go on either way.

Simiple repair. Determined drip pan size (sm, med., lg.) removed 2 screws holding drip pan, placed gasket around new drip pan and installed. Repaired took less than 5 minutes.

Removed the two screws holding the porcelain burner bowl. Disconected the electric igniter by removing the "w" clip on the underside of the bowl. Then disconnected the igniter from the electric supply cord. Reverse these directions using the new urner bowl.
Really easy.

first I removed all the srews from the burners that hold the glass cooktop. I then disconected the two wires from the damaged gas valves and replaced them all four with the new ones. After that I put it all togehter and work just fine and celebrated with a good cold beer.

I unscrewed the burners which was three screws per burner then removed gas control knobs and pulled up range top and un hooked the old module and replaced it with the new one two screws hold it in place and connected it the same way the old one was and put range back together and now it works perfect and saved me over $250.00 and part only coated around $40 with shipping great parts seller and I highly recommend partselect.com very easy fix thanks

Three were simple screw out and replace with a nut driver. The warming burner had a smaller opeining which was too large for the nut driver. Had to remove shielding aroound it first. Simple, job. My mother did the last one.

Pulled off burner grates, burner, unscrewed burner bowl, removed clip from igniter and wire, then put it all back together. Was very easy, and the stove looks like new again.

PartSelect is very good with amazing shipment times. The kjpart arrived much sooner than expected.

The most difficult part of the repair was getting the front panel off. I needed to remove the top of the stove, which was easy but awkward - remove the two screws from each of the four burner bowls. Lift the bowls one by one, disconnect the wire and slide off the small clip under each igniter. Move the bowls and igniters out of the way. You will find a piece of sealant underneath the stove top covering the length of the front panel. You need to gently pry it off by lifting the stove top just enough to break the seal. Once the top is separated just gently move it to the back of the stove. You can now remove the 3 large screws underneath the front panel. There are also 2 screws under the plastic anchors that hold the front panel in place. Be careful, there are hidden screws in the back of each anchor, so don't break them. You just need to loosen them just enough to wiggle the front panel out. With the panel moved, the igniter switches are mounted over each knob. There is a spring washer clip holding them down. Gently pry off the clip of the damaged switch and disconnect the two wires. Make sure you put the wires back in the same order.

No way to adjust mixer tube assembly so the mounting holes will line up with the holes in the burner bowl. Mounting
holes in bowl should be slotted to prevent future problems.
Had to finally bend the mixer tube mounting bracket enough to get one bowl on. It also made the procelin break
on that bowl because the screw put to much pressure on the side of the hole.

Igighter mounting hole out of position just enough to prevent the burner head from sliding over it and sitting on
the mixer tube correctly.

I solved this problem by fileing the opening slot for the igniter. Even with the igniters being just a little out of
alignment from the original position they still light well.

I did not get new gaskets for the burner bowl but would reccommend that you get them.

First I elevated range top, then removed cracked electride from connector pin. Installed new electrode and lowered range top and all was fine.

Lid Switch.
Rewiring connection.
Function is satisfactory.
Fan belt ordered is saved.
A 1970 Clothes Washer.

The replacement part not right size for the porcelain cone for gas. Had to unscrew 2 screws remove the cone, after unclicking gas wire. The gas spreader did not fit with the cone in place.

I replaced the igniter under the knob.

Replaced Spark Module and adjusted igniters

Removed several screws and removed element. Replaced same. Total ten minutes.