Models
>
JES9750BAW
JES9750BAW Jenn-Air Range - Overview
Models starting with JES9750BAW
Click on the best match to narrow your results.
Keep searches simple, eg. "belt" or "pump".
Grease Filter
PartSelect #: PS11743870
Manufacturer #: WP71002111
The filter is made of metal and is intended for use with ranges and cooktops. As per the manufacturer, this filter may be 1/2" slimmer than the original, but will still function the same.
$39.13
In Stock
Long Oven Sensor
PartSelect #: PS1570174
Manufacturer #: 12001656
This oven sensor kit comes with two harness adapters. This sensor detects the temperature within the oven cavity.
$47.67
In Stock
Touch-Up Paint - White
PartSelect #: PS385132
Manufacturer #: 72017
This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
$10.20
In Stock
Bake Element
PartSelect #: PS11752540
Manufacturer #: WPW10310274
This bake element is found on the bottom of the oven. his bake element is for ranges.
The bake element is at the bottom of the oven and supplies the heat for baking.
Unplug the range or shut off...
$130.50
In Stock
Door Gasket
PartSelect #: PS11749287
Manufacturer #: WPW10162384
This oven door gasket comes with built in retaining clips.
$111.22
In Stock
Burner Knob
PartSelect #: PS11744450
Manufacturer #: WP74011493
Sold individually. This knob accepts a D-shaped shaft.
$65.01
In Stock
Oven Rack
PartSelect #: PS11744745
Manufacturer #: WP7801P173-60
Used in the lower oven. Sold individually.
$115.55
In Stock
Insulation
PartSelect #: PS11750415
Manufacturer #: WPW10208653
Oven Wrap Insulation.
$77.41
In Stock
Cartridge Male Contact Spade
PartSelect #: PS1988157
Manufacturer #: Y708572
This cartridge assembly male contact spade is made of metal. These are sold individually, though each range uses four contact spades.
$17.79
In Stock
Terminal Block
PartSelect #: PS11750972
Manufacturer #: WPW10245259
It provides a way of connecting individual electrical wires and offers protection of the device from electrical surges (voltages and/or currents).
$43.47
In Stock
Common Symptoms of models starting with JES9750BAW
[Viewing 10 of 10]Little to no heat when baking
Fixed by
these parts
these parts
Show All
Element will not heat
Fixed by
these parts
these parts
Show All
Oven is too hot
Fixed by
these parts
these parts
Show All
Oven not heating evenly
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Touchpad does not respond
Fixed by
these parts
these parts
Show All
Door won’t close
Fixed by
these parts
these parts
Show All
Will not program
Fixed by
these parts
these parts
Show All
Door won’t open after self cleaning cycle
Fixed by
these parts
these parts
Show All
Little to no heat when broiling
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Replace Grease Filter
Just a couple of minutes to left off the cover grid, left out the old filter and drop in the new one.
Parts Used:
-
Gene from Washington C.H., OH
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
524 of 537 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven not holding 350 F, when cooling the coils did not reheat
Removed the oven door by opening slightly, then pic door up to remove. Remove 2 screws holding oven sensor in place, gently pull on sensor to remove, had to remove about 8 inches to get at plastic connector. Unplug connector, had to use an adapter cable supplied with the PartSelect kit to install new sensor, push cable back into opening, reinstall 2 screws. The oven works fine! Note that due to thermal lag the temperature overshoots to 370 degrees and undershoots to 340 degrees, this appears to be normal oven operation. Putting door back in place was easy.
Parts Used:
-
David from Westford, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
156 of 196 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
mice had made nests in the insulation wrap in the range
I numbered every part. ex: 1 L., for first part removed left side. I used a magic marker to circle the holes and wrote the number of screws used on the part, set the srews in a separete place, so that I new where these screws went to. The cleanup was pretty time consuming, but I was able to keep my stove, when every repairman I called to fix my stove told me I was better off buying a new stove. ($600.00 stove 2 years old)Please Note: The insulation blanket needed for the entire stove is two pieces, the sides and top are one part # and the bottom and back, are another part #. I did not know this. I just purchased the top and sides. I got lucky, the back and bottom were still in good shape. So I guess I should have read the description of the part more carefully to see what it covers, before I ordered it. It took two people two hours to do the work, it was really nice to have an extra set of eyes, to remember what direction pieces of metal from the stove went. I would do it all over in a heart beat instead of buying a new stove.
Parts Used:
-
Wendy from Red Hook, NY
-
Difficulty Level:Easy
-
Total Repair Time:More than 2 hours
-
Tools:Screw drivers
98 of 133 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!