JES1290SKC01 General Electric Microwave - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Microwave Was Popping And Shooting Fire Sparks
I removed the plastic plug that held the wavecover in place and pulled the wavecover off. I replaced with new cover and it worked perfect.
Parts Used:
-
JULIE from MACON, GA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
19 of 19 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
GE Wave Guide Cover was fried, needed replacement
The wave guide cover (wgc) are notoriously bad on this model. As far as I can tell even a little food that gets stuck on it combined with cooking small/insubstantial items will cause the wgc to overheat and catch on fire. Ordered a part from partselect, found it very easily on their site using a nice diagram and ordered it. The item came in two days and was a cinch to pop in and replace.
Parts Used:
-
Steven from Benicia, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
4 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
wave guide cover on fire
Remove white plastic button retainer (flipped out of my fingers and lost it. Found it 2 days later. Dog had chewed on it.) tabs on cover fit in nicely. New cover gets hot. Don't know if this is normal.
Parts Used:
-
Hugh from Alexander, AR
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
3 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
easy
no tools required. saved me from buying new microwave. glad i found this site.
Parts Used:
-
herman from franklin, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
3 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Microwave was popping and sparking flying
Removed the old wave guide cover and replaced it by slightly bending the wave guide cover and inserting 2 tabs on each side into the slots on the side of the micro/convection oven. I was ready to purchase a new appliance. Googled the model number, looked at a couple of sites and read the problems others had with this appliance and found my problem. I saved $$$ by purchasing the part and extended the life of my 11 year old appliance.
Parts Used:
-
Donna from RANGER, TX
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Power cut off to Microwave - It was run empty
1. Remove trim kit - Philips head screw driver
2. Remove Microwave from the wall - Philips head screw driver
3. Remove outer microwave cover - required tamper proof torx bit drivers
4. Replace Magnetron thermostat. On this model there are 2. in this case it was on top of the unit tied into the wiring harness to the main panel.
5. Reinstall microwave and trim kit
2. Remove Microwave from the wall - Philips head screw driver
3. Remove outer microwave cover - required tamper proof torx bit drivers
4. Replace Magnetron thermostat. On this model there are 2. in this case it was on top of the unit tied into the wiring harness to the main panel.
5. Reinstall microwave and trim kit
Parts Used:
-
Michael from POTOMAC, MD
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
unable to push fastening button into wave guide cover without cutting or tearing
-
Dale from BEREA, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door glass cracked
Remove the door and order the part. With in a day the part was at my front door. 30 minutes later was using applicance. Superb service from this company!!!!!!!!!
Parts Used:
-
Bertha from MIddle Port, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
1 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replaced magnetron and spreader plate
on the kitchen counter. Removed parts and replaced exactly as the came off. insuring all fits were tight and secure.
Parts Used:
-
Joseph from Mobile, AL
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Major sparking on right side of microwave.
Used my pocket knife to remove the locking button that holds the wave guide cover in place. Took out the old wave guide cover and cleaned the area around it. Put the new wave guide cover in place and inserted the locking button. VERY easy to do. So easy a caveman could do it!!! Seriously.
Parts Used:
-
Douglas from Waterford, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Just a little bit too big.
I had kept the old cover, just measured it against the new one, outlined it with a pencil, cut it to the correct size with a pair of scissors. Works perfectly now!
Parts Used:
-
CHARLENE from BURLINGTON, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!