JED7430AAB14 Jenn-Air Cooktop - Instructions

pulled old one out , cleaned the area & replaced with the new one.

Removed the old grease screen and cleaned the entire area thoroughly and replaced the screen

I had put up with a filter that got more and more raggedy every year, but I thought my 30 yr. old range/grill top was too old for me to find an replacement filter. What a great service you offer. I found you by web-surfing, typed in the model #, and presto--you sent me the shiny new filter. All I had to do was pop it in and throw away the nasty grill (after washing the scent off to keep the bears out of my Colorado garbage.) Thank you!

Cleaned out the downdraft cove, inserted the new filter, and put old filter in garbage can. Laughing. Thanks. Wish you had a FAQ's hotline. I'd like to know if the radiant inserts fit the older coil-type models.

Remove about six to eight screws in pan, and four screws in the on off knobs lift up. should exspose wires and ground with these two items lifted off. Two nuts on element take of to loosen element. Unhook wires. reverse and put back together. Can be a bit dirty job but very easy. Parts came in one day. One hour job tops.

The Model number could no longer be read clearly on the stove electric grill with a down draft vent system, so all I had was the size and looks of the old grease/air filter. I was very happy to come across Parts Select by way of an amazon.com search. Their web site's design and the parts pictures with detailed descriptions made it easy to find exactly what I needed. The grease filter fit perfectly in no time. I have successfully used my cooking grill again.

The lids are fastened to the underside of the unit by rivets....3 to each lid.
I used a cordless drill and small drill bit to drill through the rivets to remove the old lids and remains of the rivets.
The new lids are easily fastened back using a rivet gun ( about $20 in Lowes) using small 1/8th aluminum rivets.
No real problems.
1 thing to note is that the drill bit will pass through the old rivet by about 1/4 inch before it comes up against the upper level of the BBQ floor so do not drill any deeper.The aluminum rivets are easy to drill through and you will easily feel when the rivet is drilled through.

The 15-year-old Jen-Air stove started smelling really bad. I thought it was a dead animal stuck in the exhaust tube which runs under the floor to the outside. I flushed it out with clorine bleach, but it was still bad. It turned out to the be the grease filter. I washed it every week in the diswasher, but it just was not enough to get it clean enough. Finally, the grease went rancid and smelled really bad. This "repair" took about 30 seconds.

:-) - Just removed the old one and replace with the new one. Nothing to it. Takes 30 seconds.

To replace the knobs was easy simply pulling the old knobs of and pushing the new knobs on. Replacing the on off lites was a little harder. i had to remove the control box that the knobs were mounted on. follow the wires.One lite for the left side and one lite for the right side. The left side lite was hooked to the two left side controls and the right side lite hooked to the two right side conrols.The wires then went down under the unit to the electrical junction box and wire nutted to the main wires servicing the range. What I didn't realize is that the left front contrlo knob is the only one that controls the fan.It has fan onthe knob. the rest of the knobs are not to have fane on them.I didn't notice this when I made out the order now I have all four knobs that have fan on them.

Shut off power to range. Removed 4 phillips screws under control panel. Tip bottom of control panel up and out to unhook it from the range top. Remove half of old lens piece from slot in bottom of plastic lamp fixture. Insert smaller end of new lens through front of control panel hole. Slide lamp fixture slot over the inside end of lens until it clicks into place. Replace control panel. That's it.

turned off main ckt breaker, then removed the two leads to the burner unit at the Infinite Switch; set meter to ohms and read 20 ohms. then checked the right hand burner leads, got same reading of 20 ohms. I decided then that the infinite switch was faulty. I then made sure all wiring was in the clear and turned the ckt. breaker back on and CAREFULLY read the voltage at the Infinite-Switch terminals to the burner. No voltage (0). Ordered the part and the grill now works fine. A few words about the assembly/dissasembly: The phillips screws holding the top cover were a bit rusty, as this grill is on our pool deck. When I replaced them i put a bit of high-temp silicone grease in the threads. this grease is used for auto brake service so the grill heat should not affect it. the only difficulty I had on re-assembly was lining up the top cover with the bottom pan to insert the screws.

It is so easy. Once I found the right size of filter from the website, I ordered it right away. It came in 3 days and I just need to take out the old one and insert the new one. No instruction is necessary. By the way, the price of the filter is one third of that from Jenn-air.

removed motor, saw that stablizers were broke and went to a local parts supply shop called SUNDBERG and was given a price of about 49.00 for three stablizers. at that point i went to the internet and found PARTSELECT.COM were i found the same parts for a fraction of the price,17.00, i could not believe it! SUNDBERG customer service was horrible.PARTSELECT custormer service is great and was just over the internet,any how the repair is done no more loud noise and wife is happy again ,for awhile.thanks keep up the good work.i tell everybody about you guys.

1. Remove the exhaust vent cover, located in the center of the top of the range. It just lifts off.
2. Swivel the clamp 90 degrees to release the filter.
3. Remove the filter and throw it away
4. Place new filter in place and lock in place by rotating the swivel clamp back 90 degress.
5. Replace the exhaust vent cover