The filter is made of metal and is intended for use with ranges and cooktops. As per the manufacturer, this filter may be 1/2" slimmer than the original, but will still function the same.
This bake element has push-on terminal ends.
NOTE: This element has been updated by the manufacturer. New installation screws are required. Screws are sold separately.
This part is a replacement halogen lamp for your oven. The bulb is 25 watts and 120 volts. If your light bulb is burned out, this is the part that replaces it. Be sure to turn off power to your range ...
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch...
This gas valve knob measures approximately 2 12 inches in diameter. It is a black knob that has white lettering aroud its perimeter denoting the different temperature levels: low, medium, high, etc. T...
This surface burner head is for ranges.
Surface burner head distributes the gas through holes or slots to create an even flame across the cooking area.
Shut off the gas supply and unplug the ran...
$202.21
In Stock
Questions And Answers for JDS9860ACP
Ask our experts a question about this model and we'll get back to you as soon as possible!
4 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Mike
December 12, 2019
Oven starts up but the f1 comes on after it gets hot.
For model number JDS9860ACP
Hello Mike, thank you for writing. The error code is indicating a faulty Electronic Clock Control with Overlay. The replacement for your model is part number PS11742969. Good luck with your repair!
Was this helpful?
Thank you for voting!
Mike
March 12, 2020
Oven started smoking the control panel had f1 on it my said she had to push stop a number of times. When i came home i cut off power put it back on but nothing else comes up i checked power source its fine when u push board to turn oven on u can here a click but still doesnt come on i suspect its ic board.
For model number JDS9860ACP
Hello mike,
Thank you fro your question. The F1 error code means there is a defective control board and touch pad, thus yours would need to be replaced under part PS11742969 for your model. We hope this helps.
The gas ignitiors stopped working on right two burners at once. Gas can be lit with a match. There is no sparking sound when turning on any of the gas valves.
For model number JDS9860ACP
Hello Randy, thank you for getting in touch. We would recommend checking the spark electrode, part number PS11744110, to fix the issue. The spark electrode provides the spark to the burners. We hope this helps!
My oven was giving an F1 error. Then after 2 weeks of no errors, we are getting an F3. What needs to be replaced?
For model number JDS9860ACP
Hi Leah, thank you for reaching out. Based on our research, the F1 error code indicates a problem with the oven temperature sensor, the control, or the associated wiring, and the F3 error code indicates a problem with oven control, or the associated wiring. We would suggest checking the temperature sensor and the wire harness first. If these are fine, the issue could be with the oven control board, part number PS11742969. It monitors the temperature and controls the oven heat. You may need to replace it to fix the issue. We hope this solves your problem!
First, I unplugged the oven. Then, I removed the two screws that hold the element in place. After that, I gently pulled the element toward the front of the oven until the wires were exposed. I disconnected the wires from the old element, removed the old element and then attached the wires to the new baking element. I gently pushed the new element back into the screw holes and screwed the new element in place. When I plugged the oven back into the wall I heard a pop and thought I'd blown up the oven! Turns out the breaker popped...after fixing the breaker, I turned the oven on and the element worked just fine. I highly recommend PartSelect.com for their fast shipping and great products. I will be ordering from them again for future appliance parts.
Removed the oven door by opening slightly, then pic door up to remove. Remove 2 screws holding oven sensor in place, gently pull on sensor to remove, had to remove about 8 inches to get at plastic connector. Unplug connector, had to use an adapter cable supplied with the PartSelect kit to install new sensor, push cable back into opening, reinstall 2 screws. The oven works fine! Note that due to thermal lag the temperature overshoots to 370 degrees and undershoots to 340 degrees, this appears to be normal oven operation. Putting door back in place was easy.
