JBS55DM1WW General Electric Range - Instructions

Ordered the part on Friday, got it on Saturday, very impressive. Be sure to unplug the range or disconnect the power at the breaker box before any repairs are started.

The lower (Bake) element is held in by 2 screws. Remove them and gently pull out the element to remove the power wires connected to the element. These wires are very short and there is not much room in which to work. After having removed the wire connectors one slipped from my fingers and went back in the small opening in the back of the oven where the element is inserted. It took some time to fish out the wire. Not wanting to slide out the range I used some surgical forcepts I happen to have grab the wire ( handy to clip wires or compontents in place for some delicate repairs). Its all blind and the opening is very small plus the insulation must be pushed back to gain access. Anyway I managed to grab the wire, attached both wires to the element, replaced the plate and screws holding the element in place, all finished. Worked great. Other ranges I have owned provided a socket to plug in the element, I guess the bottom line gets in the way of quality.. Being 60 years old the worst part of this job is the getting down on my knees to do the work and getting back up again.

Removed six 1/4" hex nuts on rear of oven. Then through front/inside removed a single 1/4" hex nut to actually remove sensor. Unplug sensor connector, remove. Reversed steps, push oven back in place and plugged in. Tested oven function.

Cut the Power! pull out stove remove the 4 screws in the back, disconnect the two wires from the element.Open oven door, remove racks and remove 2 screws holding the element in place. Replace element and the 2 retaining screws, replace racks.On the back of the oven connect the two wires and replace cover. Slide back in place and turn on the power. Done =)

Repair was very simple. Removed 2 screws under the cooktop, tilt the cooktop back, unplug 4 wires from 8" burner, remove two screws holding retaining clips, install new burner in reverse order. Very simple!

First, we turned off the electricity for the whole house, since we didn't want to pull the unit away from the wall and possibly damage our new floors. We then used a socket wrench to remove the 2 nuts holding in the broken element. After that, we pulled out the old element, and this is where the difficulty came into play. The wires for the element stayed inside the back of the oven, and nothing we did could make them come out. We tried for a long time to get the wires to come back out into the oven, but our fingers were not long enough, and nothing we inserted into the space helped the situation.

Since we had turned the electricity off and still were reluctant to move the oven ourselves, we actually decided to call in a repair person (cost: $90). What he did, though was really simple:

He pulled the oven out from the wall. Used a screwdriver to open the back panel of the oven and was able to pull out the wires. Then, he inserted the new element, hooked it up to the wires, and closed back up the back panel. Then, he moved the oven back into place.

The repair person did this in all of 5 minutes, so if my husband and I had thought about the back panel, we would have easily done it ourselves.

My husband had turned the oven on to cook something and didn't know that I have a plastic tray in there. Well, needless to say I needed to get some new oven racks. I tried to get them through the manufacturer (GE). They were 68$ each. I thought that was a bit steep, so I looked online. I decided to order through PartsSelect. Well...they can 2 days later (the week before Christmas!!)and were a PERFECT fit.
Between the price, shipping speed and quality I will
definitely buy from again and recommend this site to everyone I know!!!!

Oh yeah, I work for Sears too. we have access to all sorts of parts....this site is the BEST for prices and delivery speed!!!!

After removing the back of the range the oven control board was visible and accessible by removing four nuts. There was some resistance removing the leads from the oven coils and light-bulb mechanisms but with some leverage and pliers they came loose. The only challenge was the face plate of the unit is attached using adhesive and needed to be carefully peeled off and added to the new oven control board. Getting this right was just a matter of taking time and lining up the components correctly. After applying the face, the new control board went right in. I reattached the back, plugged the unit back in, and the over has worked great for the past week. Part select being able to identify the part numbers listed from the component likely saved me at least $100 of having a GE certified repair technician come in.

The existing terminal block on my Ge oven/Range had melted due to a loose wire causing sparking and starting the plastic casing of the terminal block on fire and melting it, Part select made the part easy to find and had it at my house in 2 days. All I had to do was remove six screws to take the back sheet metal cover off of the oven. Unscrew the terminal connections remove two mounting screws that held the terminal on to the oven body. This was a little trickier than it should have been because the melted plastic had reformed making it very hard to access the mounting screws. i then mounted the new piece and plugged the oven in, it took 15 minutes and was very easy. definitely saved me at-least a $100 for the service call i would have made if finding the part wasn't so convenient

Open lid,un screw coil,pop in new coil snap holders in place,then cook a steak

called service co. and described problem while i was looking at parts diagram and he agreed with my feeling what part got fried. he told me the part would be 183.00 plus labor and drive time. when i told him i was looking at the part on line for 65 dollars he hung up on me. i recieved the part and was slightly dissapointed to know there was a sepperate adhesive overlay. i saw that it was a sepperate part but if i knew it was adhesive i would have spent the extra 20 dollars for a new one. but, to my surprise the old one peeled off easily and gently re-apllied it to the new conrol board alighning it well seemed to be the trickiest part of the job. took the five wires with connectors out of the old one and inserted them into the same place on the new one. removed the old one from the frame (4 pan phillp sheet metal screws) and then screwed the new wired control board in. plugged in the unit and pressed the bake button and then mixed the brownie batter. replaced the back panel cover. 65 dollars and 15 minutes.

thanks

bob

Unplugged appliance and removed 5 screws on back of stove/oven and removed plate. Disconnected the sensor and unscrewed it on the inside of the oven. Pulled the cord through and replaced with new sensor. Replaced all parts and plugged in the appliance and tested. Worked great.

Unplugged range. Opened oven door and removed two screws from top of oven opening. Lifted oven top and propped up
with a 2 x 3.Unscrewed the two screws that were holding

The repair went very easy. The replacement part was designed differently than the original part. It installed on the rear of the drawer with a screw as the original snapped into the side. This was a bit confusing when researching and looking up the part online.

I started by lifting the front of the stove and slipping a towel under it so it would slide easier and not scratch the floor. The next step was to unplug the stove, after that, I removed the shelves. The next step was to remove the cover plate on the b ack to expose the connection. I removed the old element by pulling the to slide-on connections and the two mounting screws. At this point I took the time to clean the oven since the element was not in the way. To install the new element I did the opposite of th removal process.

First, I made sure the power was turned off at the breaker box so I didn't electrocute myself. Then, I took out the 2 screws that hold the element in place, then pulled it out and unplugged the wires.
I plugged the wires onto the new element, and replaced the screws. My daughter could have done this....