This 9-inch radiant element sits under your cooktop and heats your pots and pans while you cook. If it’s not heating up or cooking unevenly, it’s time for a replacement. It’s the larger burner on your...
This 40-Watt light bulb is sold individually.
It is specially designed to withstand extreme temperatures, so this bulb is compatible with a variety of appliance types including refrigerators, ranges,...
The temperature sensor detects the temperature within the oven cavity. If your oven is too hot, not heating evenly, or has little to no heat when baking, you may need to replace the temperature sensor...
If your stove’s burner isn’t heating right—maybe it’s stuck on high or won’t turn on at all—this control switch could be the fix. It’s made for 6-inch burners and lets you adjust the heat smoothly, no...
If your GE stove isn’t heating evenly or one of the burners isn’t working, this dual radiant heating element could be the fix. It fits many GE flat-top ranges and has two sizes built into one—12 inche...
This part is the replacement oven bulb lens cover. It is made of glass and is approximately 3 inches in diameter. The lens cover is rigid and protects the oven light bulb from being damaged. The main ...
Is your GE range's knob assembly worn out or missing? Don't worry, we have the perfect replacement for you! Our GE Surface Burner Knob Assembly is designed to not only refresh the look of your range b...
The GE Oven Door Window Pack Assembly is a genuine OEM part that fits select GE ranges and ovens. It includes a heat-resistant inner glass panel, frame, and seals, providing insulation and clear visib...
Ask our experts a question about this model and we'll get back to you as soon as possible!
1 question answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Judy
December 6, 2023
I have double oven model. How do I set the self clean mode to self clean both at and in the same timeframe?
For model number JB850SF1SS
Hello Judy, thank you for getting in touch. According to our research, you can set a self clean cycle in both the ovens at the same time. However, they will not self clean at the same time. The last oven set will automatically delay its start until the end of the first oven’s clean cycle. When an oven is set to self clean, both the oven doors will lock and the cooktop controls will lock out. The ovens and cooktop cannot be used when an oven is set to self clean. To set the oven for self cleaning, you may need to follow the following steps:
1. Touch the self clean pad.
2. If a time other than the default time is needed, use the number pads and enter the desired clean time. You can change the clean time to any time between 3 hours and 5 hours, depending on how dirty the oven is.
3. Touch the start pad. The oven door locks automatically.
The display will show the clean time remaining. It will not be possible to open the oven door until the temperature drops below the lock temperature and locked/door goes off in the control display. The word locked/door will flash and the word door will display if you set the clean cycle and forget to close the oven door. To stop a clean cycle, touch the clear/ off pad. When locked/door goes off, indicating the oven has cooled below the locking temperature, you will be able to open the door. We hope this information helps!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
Removed six 1/4" hex nuts on rear of oven. Then through front/inside removed a single 1/4" hex nut to actually remove sensor. Unplug sensor connector, remove. Reversed steps, push oven back in place and plugged in. Tested oven function.
I had to remove the oven from the wall because the sensor plug connction is behind the unit. Two screws hold the sensor inside the oven and then I disconnected the lead and pulled the sensor out from the front. I installed the new sensor, tightened the two screws holding it in and connected the lead. Then reinstalled the oven into the wall. Overall, a very easy repair once you get the oven out.
The existing terminal block on my Ge oven/Range had melted due to a loose wire causing sparking and starting the plastic casing of the terminal block on fire and melting it, Part select made the part easy to find and had it at my house in 2 days. All I had to do was remove six screws to take the back sheet metal cover off of the oven. Unscrew the terminal connections remove two mounting screws that held the terminal on to the oven body. This was a little trickier than it should have been because the melted plastic had reformed making it very hard to access the mounting screws. i then mounted the new piece and plugged the oven in, it took 15 minutes and was very easy. definitely saved me at-least a $100 for the service call i would have made if finding the part wasn't so convenient
