This 40-Watt light bulb is sold individually and is a genuine OEM replacement option for your home appliances. It is specially designed to withstand extreme temperatures, so this bulb is compatible wi...
This rear drawer support comes with the installation screw. This part has been redesigned. The new support inserts towards the rear of the drawer as opposed to the side.
This part is a replacement lens for your oven or range. The lens is red in color, and when the elements are turned on, the light behind the lens will turn on to inform the user that the element is, in...
This part is also known as the "brains" of the appliance. ***NOTE: The wiring could be different than the original control. This part may need to be installed by an appliance repair person.
This part is the replacement light socket for your oven. The oven light socket provides power to the light, and at the same time holds the light bulb in place.
This is a replacement haliant element for your cooktop or range. It is used with flat top ranges, and is found under the glass top of the range. This element is approximately 12 inches in diameter and...
The oven door gasket creates a seal between the oven door and the opening of the oven to prevent heat from escaping when the oven is closed.
$76.70
Special Order
Questions And Answers for JB640SR1SS
Ask our experts a question about this model and we'll get back to you as soon as possible!
1 question answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Lee
July 23, 2021
How do i access the bake element in this model? I can't find any info online
For model number JB640SR1SS
Hello Lee, Thank you for your question. The element is under the bottom floor panel of the oven. To access it, first disconnect power to the appliance. Pull appliance out from the wall so left side is exposed. Next remove cooktop. Remove the outer side panel by removing the screws. There s also one hidden screw inside front of drawer section. Remove side insulation retainer and unhook the wire insulation retainers at the top. Disconnect hidden element ground wire and unplug the element. Inside the oven cavity, remove the screw in the lower left corner. Slide the element out from under oven. when reinstalling, make sure the bottom insulation is fully covering the bottom of the base module. Slide the hidden bake assembly in from the side, being careful not to move the insulation. Reconnect the side insulation retainer and element ground wire. Reconnect screw at lower left inside oven cavity. Plug the hidden element wire harness into element terminals. Reattach outer side panel and cooktop. Hope this helps!
Removed six 1/4" hex nuts on rear of oven. Then through front/inside removed a single 1/4" hex nut to actually remove sensor. Unplug sensor connector, remove. Reversed steps, push oven back in place and plugged in. Tested oven function.
After removing the back of the range the oven control board was visible and accessible by removing four nuts. There was some resistance removing the leads from the oven coils and light-bulb mechanisms but with some leverage and pliers they came loose. The only challenge was the face plate of the unit is attached using adhesive and needed to be carefully peeled off and added to the new oven control board. Getting this right was just a matter of taking time and lining up the components correctly. After applying the face, the new control board went right in. I reattached the back, plugged the unit back in, and the over has worked great for the past week. Part select being able to identify the part numbers listed from the component likely saved me at least $100 of having a GE certified repair technician come in.
The existing terminal block on my Ge oven/Range had melted due to a loose wire causing sparking and starting the plastic casing of the terminal block on fire and melting it, Part select made the part easy to find and had it at my house in 2 days. All I had to do was remove six screws to take the back sheet metal cover off of the oven. Unscrew the terminal connections remove two mounting screws that held the terminal on to the oven body. This was a little trickier than it should have been because the melted plastic had reformed making it very hard to access the mounting screws. i then mounted the new piece and plugged the oven in, it took 15 minutes and was very easy. definitely saved me at-least a $100 for the service call i would have made if finding the part wasn't so convenient