J320*01 General Electric Range - Instructions

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, reconnected the wires to the new element, reattached it to the oven and voila!

It worked. What was really cool, once I ordered the part, I received it in only two work days!

Good job folks!

Hardest part was getting the wrong element and having to send it back and reordering correct one....too many variables. Two screws inside the oven removed, pull out range and take off back and attach new element to plug ins!

Turned off power at breaker panel. Removed 2 screws attaching element to stove. Pulled element out a couple of inches and removed 2 wires attached with screws. Installation is reverse order of removal.
Be careful not to twist the terminal ends when tightening screws.

shipping was very fast!

Of course I unplugged the stove. Then I removed the cover to reveal the connections for the element. After unscrewing the two wire connectors, I had to use a nut driver to remove the two screws holding it in place in the oven. The new element went in easily. I screwed it in place in the oven and then attached the two wires in the back and replaced cover. Plugged it in, tested it, and we were good to go.

Note: this was a second attempt, The first time I ordered a heating element with push on connectors not screw on. Beware! Pay attention to the pictures and description. I ordered too quickly.

Our element blew in our oven, we took it out and saw what we needed. It was very easy to see what part we needed to order because of the great pictures on the website. The larger views really helped. We got the part quickly and put it in. It was a breeze and now our oven is working great! The best part however, is it only cost about $33.00 including shipping and handling. Much cheaper than if we would have had someone come in to fix it!

First, shut off the breaker to the stove. Removed old element by unscrewing the two screws on the plate where the element attached at the bottom of the inside of the oven. The old element was corroded at the connection, so disconnect it, attached the new one, pushed it back in the insulated socket then reattached the two screws on the plate. Flipped the breaker back on. Works great. Only took about 25 min. from start to finish.

Note: Please make sure power is off!!! Turn off at the fuse panel,Main. Test oven after you turn off breaker...try turning on oven with normal switch, indicator light should be off. Also check interior light, usually wired 110 volts, may be on a separate circuit, just for safety!!. Remove retaing screws, scewdriver will work , but a nut driver is easier. Pull old element out gently and check between terminals with volt meter. Remove screws on element holding feed wire, reverse this process to install. Test oven for proper operation after installation...make sure oven cycles through a set temperature range.

Simply took the replacement part ( PS244040, GE WB30X341) and did the quick direct swap using all the new pieces in the burner kit. UNPLUG the stove. Undo the titl arm screw, remove the plastic wire isolation block (2 spring clips), unscrew the 3 wires to the elements, screw the 3 wires to the new element, put in new bakelite wire isolation block with spring clips to keep the wires seperated, mount and titghten the tilt arm screw. Make sure the burner sits even and flat in the stove top. Plug the stove back in and test.

Finding the replacement part on partselect.com was easy. The search feature brought me to a diagram of the bake element and offered precise grid measurements to assure me it was the correct part.

Be sure to completely unplug your stove before doing anything. The only tools I used were a small nut driver, a standard pliers and a flashlight (and a cushion for my old knees, ha).

Installation was easy, but you have to be very careful to not bend the little prongs were you attach the element to the stove wires... they bend pretty easily, so hold them tight or hold them in a pliers firmly but without crushing them. Drive the two screws to attach the element to the wires; then, drive the two screws to hold the element face plate against the rear of the oven, and viola, you're done!

Thanks, partselect - website, price, packaging and shipping were perfect! Also, I got several good tips from the feedback of other customers that were very helpful. That is a nice feature of your website and a good customer service.

Before you start, make sure the circuit breaker is not tripped, which can explain element not heating.
In my case, the toaster element was ok, which tells us that the oven is receiveing electric current.
1) Take the grills out so you have free access
2) Remove the door - this model just pull it up to let it free
3) remove the 2 screws securing the element on backwall of the oven and gently pull the element out
4) if you have a multimeter:
a) set it to AC, greater than 300 V
b) use your alligator clips, attach the clips
to the contacts of the element
c) briefly turn the oven on: expect to read between 230 and 260 volts
5) remove the screws securing the old element
6) install the new element;
7) secure the element back to the backwall
8) turn the oven briefly on and feel the heating element: should come warm pretty quic;
- Job done -

When you remove the screws securing the wire to the old element, make sure the wires are not cracked, or interrupted.

Otherwise, a real simple and easy fix.

Specs of this element are what I missed but here they are:
Resitence : 25.5 Ohms
Volts: 230 - 260Volst
Power : 2050 to 2650 Watts
The power depends on the voltage, so make sure you dont have it too low (less than 220 ) or too much (yeah, 260V is nearing upper limits)

Removed the plug from wall socket.
Removed door to oven by lifting it straight up while partially open, in locked position.
Remove Baking shelves.
Removed 2 screws @ the back of element where it goes into the ovens back wall with a nut wrench and gently pull the element towards you until wires are exposed.
Using a flat blade screw driver hold on to the end of the element near the end with the screw and support it as you un screw the wire so the end of the element does not bend as you turn the screw.
After both wires are removed, remove the old element.
Install the new Element in reverse.
Very Easy!

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. connected the wires to the new element. pushed the element back in place the screwed it back to the back of the stove.

Due to this wall oven being vintage 1972, I decided to replace the broil element along with the bake element that had actually failed. The repair was pretty straight forward as seen on the videos, altough it can be somewhat tight to use screw drivers or nut drivers with long handles. You may find that shorty screw drivers or a 1/4 inch ratchet wrench and appropriate socket are easier to work with. There were two things that I was cautious about. The first was to be very gentle with the power wires since I didn't know what condition their insulation was in. I tried not to scrape them on the sheet metal opening as I pulled them gently out through the oven insulation. Secondly, I was very, very careful in moving the oven temperature sensor probe out of the way so I could undo the broil element. Before I started the job, I had learned that this probe isn't a separate piece part, it is part of the entire THERMOSTAT ASSEMBLY for the stove and it's not readily available. Furthermore, this assembly costs $250 to $350 !!!! The only negative with this job was that the old broil element has some kind of heat resistant material on the rear of the plate that attaches it to the oven wall. This old material fell apart during disassembly. I kind of pieced it back together during assembly, but I would have liked to have been told I needed this piece (since there wasn't an exploded parts view on the web for me to look at)or a new piece of this material should have been supplied as part of the broil element.

Used socket set to remove bolts holding the elements in place, then used a screw driver to remove the wires from the elements. Replaced with new elements, screwed in the wires and reattached the elements to the wall with the bolts.
It was easy, it was just a small space to work in.

Shut power off. Removed two outer screws, pulled heating element forward and removed two more screws. Ordered part and it arrived in three days. Installed in reverse order of removal. Easy fix. Cost was reasonable.