IRFBF021WK DeVilbiss Compressor - Overview

This replacement screw is a genuine OEM sourced item commonly utilized on air compressors and pressure washers. It is a standard hardware which has multiple applications depending on the unit. Please make sure to check diagrams of your model for the correct location and used of this screw. This part is made from durable metal and it is sold individually. You will need a wrench to install or remove this hardware.

This safety valve is a genuine replacement part manufactured for use with air compressors. If the compressor's pressure switch malfunctions and does not turn the motor off when the amount of pressure is met, the safety valve will open to release the extra air pressure. The amount of pressure required to open the safety valve is set by the...Read more tension of the spring inside the valve. The spring can wear out, and leave the valve open at a lower pressure than what is set to turn the switch off, and will not allow pressure to build inside the tank. Please make sure to refer to the appropriate diagrams of your model for the correct location and application of this component. Keep in mind this high-quality part is made of durable metal and is sold individually.

This rod kit is an original part from Craftsman for air compressors. This part attaches to the piston to the crankshaft that is in the pump. This kit includes the following: cylinder head, piston, cylinder head gasket and piston ring. You will need a wrench set and socket set to replace this part. When installing this part, it is recommen...Read moreded that that you fasten the top screw (50-60 inch- pounds). This kit is made of metal and rubber.

This assembly fastener is supplied directly from the original equipment manufacturer. The screws are constructed of metal, and are compatible with many compressor machines. This part is often used to secure the compressor shroud. It is recommended to refer to specific manual and diagrams for repair instructions. This part is sold individu...Read moreally. Purchasing spare screws is also encouraged, as they can wear out over time and regular use. A hex key and a screwdriver are helpful in the removal and replacement.

O-rings are made to contain thousands of PSI pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. rnrnThere are many causes for O-Ring failure. The most common among power tools are: • Extrusion and Nibbling - The O-ring has ragged, tattered edges. ...Read moreThese are commonly caused by pressure spikes which shear off tiny "bites" from the o-ring, or caused by clearance gaps. • Abrasion - One or both sides of the o-ring appear rough and slightly flattened. Commonly caused by a contact surface that it too rough, contains grit or is too smooth to allow lubrication. • Over Compression - The O-ring is flattened on both sides and may have a "ring" split along its length. Commonly caused by excessive pressure or heat. • Heat Hardening - The O-ring has a pitted or cracked surface, and is often flattened on both sides. Caused by temperature exceeding o-ring capacity. • Weather/Ozone Cracking - The O-ring is covered in small surface cracks. Caused by exposure to ozone, UV rays and air pollution. Excessive seal stretching (greater that 5%) causes similar cracking.

This is a genuine OEM part that is intended to be used with air compressors from Porter Cable, DeVilbiss, and Black & Decker. The regulator is used to adjust the level of pressure in the tank. This item is sold as an individual replacement part.

This is an authentic OEM part. The filter is used with air compressors from Porter Cable, DeVilbiss, and Black & Decker. The foam filter is used to prevent dirt and debris from entering and potentially damaging the pump. A hex driver, or screwdriver may be needed to install this item and it is sold individually.

This is a manufacturer approved replacement muffler used on air compressors. Muffler softens the noise coming from the engine and provides an additional filtering. This Kit includes the Plastic Filter Holder, Foam Filter, Two (2) Plastic Pins used to attach it and a Metal Mesh Screen.

It is an OEM component which is designed for use with air compressors. This special nut sleeve assembly secures the pressure relief tube to the pressure switch. It is a high-quality replacement for a damaged or a missing hardware that was installed on a new unit. One durable metal nut sleeve assembly is included. A wrench will be needed t...Read moreo perform this repair. Check the appropriate diagrams for your model to ensure the proper replacement procedure. Make sure to drain the air before starting this repair.

This is a genuine replacement part manufactured for use with air compressors. This hex head screw has many applications from fastening the connecting rod, to securing the isolators. The screw is sold as an individual replacement part, please see model diagram for part location and usage.