HTDX100EM4WW Hotpoint Dryer - Overview

This authentic, white Drum Bearing Slide, also known as the bearing drum slide, glide, or pad, is a plastic, easy-to-install part for your dryer. It replaces the dryer's front drum slide to allow for easier movement. You'll know if this part is an issue if your dryer is unable to tumble properly or is very noisy. Damage can come from reg...Read moreular use. The part attaches to the outermost side of the bearing. Check both slides for signs of wear, because they often wear at the same rate, and should be replaced at the same time; there are 2 of these particular slides per dryer. This part is sold individually, so you'll need to purchase multiple parts if replacing both at the same time.

This Drive Belt is 89.5" long and comes in black, featuring four ribs on the inside for a better grip. This is a long belt that wraps all the way around the dryer drum, around a tension pulley, and then around the drive motor pulley, allowing all the parts to work together, spinning the drum as the motor rotates. If the drum will not turn...Read more when the dryer is turned on the belt is likely broken. It is common for belts to stretch or become brittle over time, which is what leads to the breakage. If broken, it should be replaced; the drum simply cannot spin without this belt. Refer to your model number and user manual to check if this part is right for you. Ensure you use work gloves to protect your hands from sharp internal parts during this repair. Please note: When comparing the length of your old belt to the length of the belt as stated here, remember that a small amount of stretching and contortion may occur with belts over time for a range of different reasons. Unless your belt is drastically different in length, this belt is what you are looking for despite any small inaccuracies. You will need to remove power to your appliance, remove the main panel, and access the motor drive to slip your new belt back into place.

This OEM Timer Knob is a white plastic knob which can be easily installed onto your machine's timer rod, in order to control the timer. If the part breaks off, it should be replaced. Refer to your user manual and model number to see if this part is right for you. It is a three-inch-diameter part that accepts a D-shaped shaft. To replace y...Read moreour faulty knob, simply pull the existing knob straight off the shaft and install the replacement back onto the shaft. No tools are required. This item is sold individually and is not part of a set. The timer knob contains the insert as well as the knob itself.

If your dryer’s making loud noises or the drum seems shaky, this rear bearing sleeve might be the fix. It helps the drum spin smoothly and stay in place. When it wears out, you might hear squeaks or notice your clothes aren’t drying as well. Made for GE and Hotpoint dryers, this part is a simple way to get your machine running quietly and efficiently again.

TThe door strike for your dryer is mounted on the dryer frame that the door shuts onto. It fits into the door catch on the door and keeps the door closed. If the door strike is damaged or missing, the door will not lock properly and not only will this cause the door to swing open, but it won’t allow the dryer to start properly. It is a small piece of metal, about 1 inch in length and is sold individually.

This rear drum bearing kit comes with a shaft, bearing and installation instructions. The bearing plate comes with a slot in it for the ground strap. Helps keep your dryer running as smoothly as possible with as little noise as possible. NOTE: Bearing plate has slot in it for ground strap.

Restore dependable startup functionality to your dryer with this replacement push-to-start switch, designed to activate the appliance when pressed and released. Compatible with a range of dryer models, this switch is a key component in initiating the drying cycle. If your dryer won’t start or begins running without pressing the button, th...Read moree switch may be faulty and should be replaced. Installation is straightforward and requires only a Phillips and flathead screwdriver. For safety, always disconnect power before beginning the repair. Once the control panel is removed, the old switch can be disconnected and the new one installed with minimal effort. Sold individually, this part offers a simple and effective solution for getting your dryer back in working order.

This part is the replacement high-limit thermostat or safety thermostat for your dryer. The high-limit thermostat is found on the upper right-hand side of the heater housing, and it cuts off power to the dryer motor if the temperature reaches an unsafe level. If you push the start button and nothing happens, the high-limit thermostat shou...Read moreld be tested for continuity and replaced if the contacts are open. Be sure to disconnect power to the dryer before you begin this repair. This part is sold individually and is an OEM part.

This is a replacement O-ring for the drum bearing retainer on your dryer. The drum bearing is found at the back of the dryer drum. The O-ring is designed to create a seal on the drum bearing. The O-ring is made of rubber, and can occasionally wear down and break. If you notice that your dryer drum bearing is worn while you’re replacing t...Read morehe O-ring, you should consider replacing it as well. This product is sold individually, and is an OEM part from the manufacturer.

This knob accepts a D-shaped shaft.

This part is on the outer door of the dryer.

This dryer lint filter screen is used for many clothes dryers. The frame is white and comes one per package.