This is the replacement charcoal filter for your microwave. It is silver and black in color and measures approximately 10 inches by 2 ½ inches. The charcoal filter removes cooking odors from the air that circulates through the microwave vent. You will likely need to replace the charcoal filter if you notice any damage to it, or if it has...Read more been in your microwave for a long time. This part is sold individually and is an authentic OEM part sourced directly from the manufacturer.
Uneven tray movement or loud rattling can be caused by a cracked roller ring or a wheel that no longer turns. The ring supports the glass tray and helps it rotate smoothly during cooking. First remove food buildup and check the tray, center drive piece, and oven floor for damage. Match the replacement to the full appliance model because r...Read moreing size and wheel position can vary. Disconnect power before inspection and handle the glass tray with care. Set every wheel flat in its guide, then turn the tray by hand to check its movement.
This turntable motor is for microwaves.
The turntable motor rotates the glass tray inside the microwave oven.
Because high-voltage capacitors in a microwave can retain a lethal electrical charge even when the microwave is unplugged, a service technician should install this part.
Make sure your microwave heats food evenly with this 13.5-inch glass turntable tray. It’s made from durable, heat-resistant glass and fits many GE and Hotpoint models. The underside has three grooves that help it sit securely on the rotating support, so your meals cook consistently. Just place it in the center and you’re ready to go.
Ask our experts a question about this model and we'll get back to you as soon as possible!
We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
Next
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Ronald - For model number HMV1630DBWW
September 7, 2023
how do you replace the door handle?
Hi Ronald, thank you for your inquiry. To remove the door handle, first, you may need to open the door and by using the putty knife, pry off the inner door trim to expose the screws holding the handle in place. Unthread the screws to remove the old handle and then install the new part. We hope this is helpful!
4 peoplefound this instruction helpful.
Was this helpful?
Thank you for voting!
Leeda - For model number HMV1630DBWW
November 23, 2024
I am looking for a stainless steel microwave oven handle match
Hi Leeda, Thank you for contacting us. The Silver Handle for this model is listed as PartSelect Number PS12582569. Thank you for the inquiry, good luck with the repair!
Was this helpful?
Thank you for voting!
Christopher - For model number HMV1630DBWW
September 9, 2025
I need a replacement door handle for my over stove microwave, can you help me with this
Hi Christopher, thank you for reaching out. The handle you are looking for is part number PS12582570. Glad to be of help!
Was this helpful?
Thank you for voting!
Janet - For model number HMV1630DBWW
May 18, 2026
There is a cardboard looking square piece covering an opening on the right side of the oven. A tab that holds the piece in place broke off and it won't stay on now. Is there a replacement piece for this?
Hello Janet, thank you for the question. Yes, the waveguide cover for your model is part number PS11762217. We hope this is what you were looking for!
Was this helpful?
Thank you for voting!
Prev
1
Next
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
1. Unplug unit 2. Open door, remove two screws above the top trim piece, slide and remove trim. 3. Remove screw behind control board and top left corner, then release from position. 3b. Unplug all wire terminations and set control panel aside. 4. Remove two screws securing latch board, lift and rotate board
... Read moreout of position, remove three micro switches, xfer monitor switch actuator from lower pin in old board and insert in new. Install new door switches and reverse procedure to complete repair.
Note 1. Take care to located new latch board so holding tabs line up, pass through frame, and openings for door tangs line up with openings in frame before securing with screws.
Note 2. A long magnetic screwdriver is helpful.
Read less
Was this helpful?
Thank you for voting!
Had to replace charcoal filter
15 of 25 peoplefound this instruction helpful.
Jared from SIERRA VISTA, AZ
Easy
15 - 30 mins
Open the front cover by pushing it at the top (where it says “Push”), lifting up and pushing back on top edge of the old filter. Pull it out. Installing the new one is basically just the reverse of those steps! That simple.
Old filter did seem to be a little thicker (filter material), but the new one was the exact same dimen
... Read moresions, so it went in properly. Wish the filter material was white, so you knew just how dirty it was actually getting. But... :-D
Read less
Was this helpful?
Thank you for voting!
Mirowave door latch
6 of 11 peoplefound this instruction helpful.
Fernando from WEST CHESTER, PA
Really Easy
Less than 15 mins
While installing a filter in my brand new never been used microwave range hood combo I snapped off the top door latch with my elbow. After a few expletives I search You Tube and found it was a simple fix. I ordered a replacement latch from this site. It arrived in three days and it took 5 minutes to fix.