HLP28E Haier Washer - Overview

Diagrams for HLP28E

See every part. Know exactly what you need.

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Drain Pump – Part Number: WH23X27419
$98.25
Special Order
Drain Pump
Part #WH23X27419
A washer that stops mid-cycle or leaves water in the drum may have a blocked or damaged drain pump. The pump uses an internal impeller to push wastewater out through the drain system. First check the drain hose, filter, and pump inlet for kinks or trapped debris that can mimic pump failure. Match the replacement to the appliances full model number and electrical connections. Disconnect power and water before opening the cabinet, prepare for residual water, and keep wiring dry. After installation, run a short cycle and inspect every connection for leaks.
Water Inlet Valve – Part Number: WH13X26636
No Longer Available
Water Inlet Valve
Part #WH13X26636
BRACKET - DRAIN PUMP – Part Number: WD-0850-73
$5.72
Special Order
BRACKET - DRAIN PUMP
Part #WD-0850-73
SCREW ST4X14 – Part Number: WH02X26514
No Longer Available
SCREW ST4X14
Part #WH02X26514
TAPPING SCREW – Part Number: WH02X26155
No Longer Available
TAPPING SCREW
Part #WH02X26155
Hose Connector – Part Number: WH01X27831
No Longer Available
Hose Connector
Part #WH01X27831
Drain hose clamp
Actuator Motor Brake – Part Number: WH20X27368
No Longer Available
Actuator Motor Brake
Part #WH20X27368
WASHING MACHINE CLUTCH – Part Number: WH38X27398
No Longer Available
WASHING MACHINE CLUTCH
Part #WH38X27398
DRAIN PIPE – Part Number: WH41X27715
No Longer Available
DRAIN PIPE
Part #WH41X27715
WASHING MACHINE CONTROL PANEL SEAT – Part Number: WH44X26195
No Longer Available
TAPPING  SCREW – Part Number: WH02X26189
No Longer Available
TAPPING SCREW
Part #WH02X26189
WATER LEVEL SENSOR – Part Number: WH12X26184
No Longer Available
WATER LEVEL SENSOR
Part #WH12X26184

Common Symptoms of the HLP28E

How this model fails, and the parts that fix it.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
The water stopped draining.
8 of 10 people found this instruction helpful.
  • ILANA from NEW YORK, NY
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Screw drivers
I emptied all the water with a cup and laid the washer down on its back on the bathroom floor, ( it is a portable), with a few small pots and rags handy to collect water, just in case.
I inspected the placement of the broken drain pump, I took photographs of all the wires placements and screws. I removed the broken drain pump pho tographing each step, then attached the new drain pump following each step in reverse and attached the 2 colored wires to the remains of the colored wires attached to the washer. I used electric tape to isolate and cover completely the exposed wires parts i joined. I then screwed everything back in place. I put the washer upright, connected the electrical cord and did a test. It is working great, and the water is draining well! It took me over 30 minutes, as the space under the machine, where the drain pump lodges, is quite tight and I needed a flash light.
Was this helpful?
Thank you for voting!
Washer wouldn't drain.
4 of 8 people found this instruction helpful.
  • GABRIEL from GANADO, AZ
  • Really Easy
  • 30 - 60 mins
  • Wrench (Adjustable)
Lifted up the washer from the bottom. Accessed the pump, unscrewed the motor and pulled off the rubber hose attached to the pump using a Phillips screwdriver and a wrench.
Reattached the hose and the mounting screws. Worked just fine.
Was this helpful?
Thank you for voting!
Replace inlet valve
2 of 5 people found this instruction helpful.
  • Annette from SEATTLE, WA
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
Easy. Just need to remove top and 1 panel to access. Not too tight of a workspace.
Was this helpful?
Thank you for voting!