This OEM-compatible screw is designed for use with many GE dishwashers. Measuring 8-16 HXW and 1/2" in length, this stainless steel screw secures the middle spray arm hub to the upper rack assembly, e...
Are you struggling with a malfunctioning washing machine? We have just the solution you need'the GE Drain Hose. This simple but essential part is tailor-made for washing machines, tasked with safely d...
Having trouble with your GE washer? Our Nut Hub could be just the solution you need. This little device has a big job ? it tightly secures your washer hub to the gear case shaft. Its accuracy helps yo...
You're looking at the GE 5 Solid Water Valve, the lifesaver your washer needs right now. This trusty part controls the flow of water into your machine, making sure its thirst for water is met just rig...
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
6 questions answered by our experts.
< Prev
1
2
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Janice
September 8, 2022
At start my spinner has no movement. What seems to be the problem?
For model number GTWN8250D0WS
Hello Janice, thank you for your question. We recommend checking the Impeller Insert part PS8756953 and the Impeller part PS11763314 that the insert connects into. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you.
My washer will not drain and go into rinse and spin mode
For model number GTWN8250D0WS
Hello Dustin, thank you for contacting us. Please inspect drain hoses (part number: PS8757195) and tubes for blockages and kinks. Also, inspect the drain pump, part number PS8757171, for functionality and clogs. If any of the above parts are damaged you will have to replace them. If you would like assistance placing an order, please contact customer service. Good luck with your repair!
Hi Rebecca, thank you for your question. You may have to look inside of your appliance to see exactly where your leak is coming from. However most of the time the part to check would be your drain hose. Good luck with your repair.
Was this helpful?
Thank you for voting!
Perry
March 18, 2020
My top load washer sounds like when you put a baseball card in the spokes on a bicycle. When it’s spinning
For model number GTWN8250D0WS
Hello Perry, thank you for your question. We would recommend removing the wash plate at the bottom of the tub to see if you can locate anything stuck there. If that area is clear then you would want to check the gear case and bearing and mode shifter. I hope this helps.
Was this helpful?
Thank you for voting!
Stephanna
November 11, 2022
Washer on start switch doesn’t work
For model number GTWN8250D0WS
Hello Stephanna, thank you for the question. We have researched your model and found that the issue is probably with the body assembly, part number PS8259953. If that does not work, we recommend replacing the control and firmware assembly, part number PS9491776. Please reach out to customer service if you need help placing an order. Glad to be of help!
This procedure was completely different from any other Tub Seal I've done and in my opinion needs 2 people. The first thing to note is that this seal must be removed from the bottom of the outer tub. Also, the top of this machine does not hinge in back. The typical clips are in front, but the back has 2 screws that must be removed. Since the wiring was too involved to completely separate the top from the base, I had to improvise a stand to hold the top while the rest of the process was completed - keep slack on all remaining connected wires. The motor, clutch and bearing plate must be removed from the bottom in order to access the Tub Seal. Below are the steps I did to complete the process: - Remove Control Panel Cover (rear) - Disconnect as many wire harness plugs as possible from Control Board (Note positions for reassembly - pictures work well) - Remove Pressure Switch - Disconnect Detergent and Softener dispense hoses from Machine Top - Rotate top 180 degrees (Flat-Spin) and position so no strain is on the still connected wires. - Remove Tub Cover - Remove Impeller (Agitator) from inside tub. - Remove Tub Nut - Note Left handed Threads (I used 1/2" Drive Impact) - Remove rear Cross Bar from cabinet (Cross Bar must be removed since tub will not fit through opening. Once removed it must be held in place or outer tub will fall) - Remove Inner Tub - This tub is heavy and fluid-balanced. Mine required 2 people to wobble and pull for removal. - Replace Cross bar to keep unit stable - Lay machine on its side - use care not stretch or pull any wires. - Remove motor, (Rotor and Stator) - Remove Clutch and wires - Loosen all wire ties (Use tiny screwdriver to release ties - Do Not remove the tie mount) securing wires to Bearing Plate and push wires to the outside edge of bearing Plate - Remove all screws securing Bearing Plate to Outer Tub - Use flat-head Screwdriver to gently pry Bearing Plate away from outer tub (Quite Heavy - Use Care) - Tub Seal is now exposed on top of Bearing Plate and can now be removed and replaced (Be sure to clean all seal mating surfaces and lubricate with dish soap) - Reverse this sequence in the exact order for re-assembly taking care to reconnect all wiring plugs and ground wires. - During Re-assembly I used Blue Loctite on all bolts securing the Clutch, Stator, and Rotor as I found several very loose on my machine
Secured power and supply lines. Took off rear panel. Labeled all 5 electrical inputs to water valve. Could not get water valve out. Found the 5 hoses that were clamped to the 5 valve inputs by going head first into the washer. Did not order the clamps!!!! Even if we had, we couldn't figure out how to access them. Called appliance guys who installed valve and clamps.
