GTWN3000M0WS General Electric Washer - Overview

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
DAMPENING STRAP 2PACK – Part Number: WH01X39337
No Longer Available
DAMPENING STRAP 2PACK
★★★★★
★★★★★
(9)
Part #WH01X39337
The tub dampening straps support the wash tub and reduce vibration by keeping the tub at the center of the cabinet. If your washer shakes and moves, or is making a loud banging noise during the wash cycle, the washing machine tub could be off-balance, meaning one or more of these straps may be loose, or broken. Other symptoms include: the washer leaking, not agitating, or pumping but not spinning. These straps are sold individually. However, we recommend that you replace all 4 straps at the same time. It is also recommended that you check the tub for cracks where these straps mount.
D-Shaped Knob Clip – Part Number: WH01X10106
No Longer Available
D-Shaped Knob Clip
★★★★★
★★★★★
(5)
Part #WH01X10106
Sold individually.
Tub Seal – Part Number: WH02X10383
$27.58
Special Order
Tub Seal
★★★★★
★★★★★
(4)
Part #WH02X10383
The main tub seal is located between the transmission and the outer tub. It's the primary water seal in the outer tub for the transmission-shaft. This seal is difficult to replace and should probably be installed by a qualified technician.
Dual Action Agitator – Part Number: WH43X10034
$142.92
Special Order
Dual Action Agitator
★★★★★
★★★★★
(21)
Part #WH43X10034
This does not come with the fabric dispenser - must order separately or use original part.
Tub Bearing – Part Number: WH2X1198
$47.16
Special Order
Tub Bearing
★★★★★
★★★★★
(4)
Part #WH2X1198
This tub bearing goes in your washing machine. You will find it on the bottom of the outer tub, where the transmission goes through the tub. If you hear metal on metal when the washer is spinning, you may need to replace the tub bearing. This bearing is made of metal, and is approximately 3 inches wide and 2 inches tall.
Tub Bearing Washer – Part Number: WH2X1197
$13.95
Special Order
Tub Bearing Washer
Part #WH2X1197
Split Ring – Part Number: WH02X10265
No Longer Available
Split Ring
Part #WH02X10265
This split ring is two inches in diameter.
Drain Hose – Part Number: WH41X10096
$79.66
Special Order
Drain Hose
★★★★★
★★★★★
(4)
Part #WH41X10096
This drain hose is a replacement part for your top-loading washer. The hose measures 57 inches in length.
Drain Pump and Motor Assembly – Part Number: WH23X10030
$137.13
Special Order
Drain Pump and Motor Assembly
★★★★★
★★★★★
(8)
Part #WH23X10030
This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time.
Agitator Coupling – Part Number: WH43X10032
$92.82
Special Order
Agitator Coupling
★★★★★
★★★★★
(5)
Part #WH43X10032
Bolt not included. This part connects the transmission drive shaft to the agitator base.
Knob, Gray – Part Number: WH01X10462
$17.64
Special Order
Knob, Gray
★★★★★
★★★★★
(1)
Part #WH01X10462
This knob for your dryer accepts a D-shaped shaft.
Compression Ring – Part Number: WH02X10093
$27.95
Special Order
Compression Ring
★★★★★
★★★★★
(1)
Part #WH02X10093
Used in conjunction with the timer dial knob assembly.

Manuals & Care Guides for GTWN3000M0WS

Click to download

Questions And Answers for GTWN3000M0WS

Ask our experts a question about this model and we'll get back to you as soon as possible!

Sort by:
  • 1
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Bobbiejean - For model number GTWN3000M0WS
September 15, 2022
I need a motherboard for this washing machine how do I find it
Chris Boyle Profile
Hi Bobbiejean, Thank you for your question. There is no electronic control board listed for your washer, but there is a timer located behind the right-hand side of the control panel. The part number listed under your model number for the timer is PS3487294. If you need help placing an order for it, customer service is open 7 days a week and anyone will be happy to assist you. Please feel free to give us a call. We look forward to hearing from you!
$676.47
Special Order
Washer Timer
Was this helpful?
Thank you for voting!
Lori - For model number GTWN3000M0WS
December 28, 2022
Need a control knob only
Chris Boyle Profile
Hi Lori, Thank you for your question. The part number listed under your model number for the control knob assembly is PS3499713. If you need help placing an order for it, customer service is open 7 days a week and anyone will be happy to assist you. Please feel free to give us a call. We look forward to hearing from you!
$9.37
Special Order
KNOB Assembly CONTROL
Was this helpful?
Thank you for voting!
Tim - For model number GTWN3000M0WS
August 23, 2023
trying to get to the tub bearing to replace it, have gotten the tub nut off, but the inner tub is not lifting out as videos of similar ge models show. is there something further to getting it out that needs to come off? thanks tim
Chris Boyle Profile
Hi Tim, thank you for reaching out. We have included a video that comes with installation instructions for Tub Bearing, part number PS271510 which is for your model. We hope this helps.
$47.16
Special Order
Tub Bearing
Was this helpful?
Thank you for voting!
Cheri - For model number GTWN3000M0WS
March 27, 2024
My machine will not spin after the wash cycle but will spin on final drain & spin.
Chris Boyle Profile
Hello Cheri, thank you for getting in touch. Based on our research, the issue is most probably with the timer, part number PS3487294. It controls most of the operations of the washer, such as water level, tub filling and emptying, length of cycles, and cycle setting sequences. You may need to replace it to fix the issue. We hope this helps!
$676.47
Special Order
Washer Timer
Was this helpful?
Thank you for voting!
  • 1

Common Symptoms of the GTWN3000M0WS

How this model fails, and the parts that fix it.

Watch our pros, then fix it yourself.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Washing Machine was not draining water from tub.
304 of 334 people found this instruction helpful.
  • Gerald from Midlothian, VA
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers
1. Drained the wash tub by taking the drain hose from the back of the washing machine and dropping it below the tub - water flowed out of hose a lot easier than trying to suck water out of tub using a pump (tried this on the first time I tried to fix washer). (Washing machine on 2nd floor of house and didn't want water running on floor)< br />2. Removed the 2 bolts holding the Pump/Motor assembly to the machine.
3. Removed both hose clamps on the Pump/Motor assembly and removed Pump.
4. Attached the new drain inlet hose to the pump and then to the tub with the original hose clamps.
5. Attached the drain hose to the pump and then plugged in the 2 wires for the pump.
6. Plugged in the washing machine and everything worked.

NOTES:
1. Hardest part was working with hose clamps (spring type clamps) in the tight space under the machine.
2. Easier to fix since I pulled machine apart a few days before - removing the clog in the pump/motor assembly only to get everything back together to find out that the motor was dead. Still well worth the time and effort due to not having to go out and buy a new Machine...
Was this helpful?
Thank you for voting!
machine would not drain all other functions seemed o.k
89 of 93 people found this instruction helpful.
  • douglas from danby, VT
  • Easy
  • 30 - 60 mins
  • Socket set
Aside from getting the wet clothes and most of the water out,the toughest part of the job for me was to figure out how to get inside the machine. I nearly wrecked the thing trying to lift the top panel. After some frustration I removed the star-type screws on back of the control panel and found, tucked away neatly, the documentation/parts list complete with instructions on how to remove the FRONT panel. Once I got inside it was easy to locate the pump. I ran the drain cycle for a moment to see if the pump turned at all. The original had an exposed fan so it was easy to see that indeed the motor was not turning. I inspected all the hose and electrical connections to make sure I had the tools I'd need and the savvy to replace the part(s) if I could locate them. I'm not much of a web-head, so I was a little surprised when I typed G.E. appliances and the search took me to partselect.com where I was pretty much coached through the procedure before I even ordered the part. The box arrived ahead of schedule (yay) and when I looked at the pump it didn't look much like the one I was replacing. But then I realized it was the same thing just ten years more advanced. I used a small pair of vise grips to pinch and lock the pipe clamps open. I know there is a plier made for this, but... Anyways, after loosening the clamps and sliding them away from the pump I pulled the hoses off and let the last of the rinse water still in them run down my shirt sleeve to my elbow. (optional, not recommended) Thus refreshed I then rummaged through my socket set and found what I needed to remove the 2 sheet metal mounting screws and disconnected the 2 power leads. I removed the faulty pump and proudly showed it to my wife. Unimpressed, she asked how much longer. I quickly reversed the procedure to install the new unit and confidently piled in a load of laundry. The cycle completed just fine and has done so since. I will and have recommmended partselect.com to friends and will use it again for sure.
Was this helpful?
Thank you for voting!
Bearing on the transmission to tub wore out (mostly due to the washer not being level)
89 of 106 people found this instruction helpful.
  • Victor from League City, TX
  • Difficult
  • More than 2 hours
  • Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
The back of the control panel had an instruction pamplet that was very useful. 2 parts did not go as written tho. To "pop" the spinner out, required short 1x4s and a shake/shingle bar to pry it up and the wedging of the 1x4s under it, until enough strain was put on it to "pop" it off. Then the large 1&11/16 nut was a bear. It require d a short pipe wrench (so it fit in the tub) and a hammer to brake it loose.
Was this helpful?
Thank you for voting!