The tub dampening straps support the wash tub and reduce vibration by keeping the tub at the center of the cabinet. If your washer shakes and moves, or is making a loud banging noise during the wash cycle, the washing machine tub could be off-balance, meaning one or more of these straps may be loose, or broken. Other symptoms include: the...Read more washer leaking, not agitating, or pumping but not spinning. These straps are sold individually. However, we recommend that you replace all 4 straps at the same time. It is also recommended that you check the tub for cracks where these straps mount.
This easy-to-use white knob helps you control your GE washing machine’s settings like cycle time and temperature. If your current knob is cracked or loose, this replacement makes it simple to get your washer working like new again. Just pop the old one off and press the new one on—it’s a quick fix that brings back smooth, reliable control.
The main tub seal is located between the transmission and the outer tub. It's the primary water seal in the outer tub for the transmission-shaft. This seal is difficult to replace and should probably be installed by a qualified technician.
This tub bearing goes in your washing machine. You will find it on the bottom of the outer tub, where the transmission goes through the tub. If you hear metal on metal when the washer is spinning, you may need to replace the tub bearing. This bearing is made of metal, and is approximately 3 inches wide and 2 inches tall.
This timer dial with compression ring shows you which part of the cycle your washer is in. It is white in color and can be found mounted on the timer shaft. You may need to replace this part if your old timer dial is cracked or damaged, or if it is not indicating correctly. This part is sold separately from the timer knob, and the timer knob clip.
Ask our experts a question about this model and we'll get back to you as soon as possible!
We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
2
Next
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Lisa - For model number GTWN2800D0WW
August 12, 2021
I am getting black marks on clothing that is near the bottom of the basket, up against the tub after the spin cycle. I have cleaned the washer using vinegar and bleach, but it is still happening. Not sure what is causing this.
Hello Lisa, Thank you for the question. This is normally caused by a worn or defective Tub Oil Seal, PartSelect Number PS4704237. We hope this helps!
The cold water valve will not open during a normal cycle when "Cold" is selected at the temperature selector. The cold water valve will energize during a rinse cycle, though. I have replaced the temperature selector switch. What is my next step?
Hi Vince,
Thank you for your question. If the cold water valve will not open during the normal cycle. the issue may be with the lid switch assembly. The lid switch on a top load washing machine is a safety device designed to prevent the motor circuit from operating when the lid is open. On some models, the water inlet valve circuit is also controlled by the lid switch. If the lid switch fails on these models, power cannot be supplied to the water inlet valve. If you have determined that the water inlet valve on your washer is not receiving power, then you should check the lid switch. Before removing and testing the lid switch from the washer, please unplug the washer from the electrical outlet. Once you have located it, verify that the actuators or levers are not sticking or damaged and that the switch is being operated mechanically. If no issues are found above, remove the switch in order to test it for continuity and set your multimeter to Rx1. While pressing in on the switch’s button, touch the terminals with the probes. You should receive a reading of zero or nearly zero. If you receive a different reading, you will need a replacement lid switch. If the lid switch is fine, you will need to check the water inlet valve and the timer. We hope this helps! If you have any questions, please let us know.
What would cause the washer to shake violently to the point where the console would come loose? Assume the washer is level.
Hello Michael, thank you for getting in touch. Based on our understanding of the issue, we would suggest replacing the shock dampening device, part number PS271100, to solve the problem. We hope this helps!
1 personfound this instruction helpful.
Was this helpful?
Thank you for voting!
Daniel - For model number GTWN2800D0WW
March 20, 2020
The above belong to a clothes washer which leaves lint on clothing after wash..is there a filter that need to be replaced in the washer. thank u
Hello Daniel,
Thank you for your question. We apologize, but the part you're looking for is discontinued and no longer available from our website. We suggest getting in contact with the manufacturer to find a substitute replacement part that would be compatible to your model. We hope this helps.
1 personfound this instruction helpful.
Was this helpful?
Thank you for voting!
Joseph - For model number GTWN2800D0WW
December 8, 2024
The wash machine won't drain
Hello Joseph, Thank you for your inquiry. We would recommend checking the drain pump and drain hoses for any clogs and you can also test the drain pump with a multimeter. Good luck with your repair.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Control knob teeth were worn
510 of 517 peoplefound this instruction helpful.
Charles from Dallas, GA
Really Easy
Less than 15 mins
Pliers
I spoke to a very nice young ladie who took my order and I received my order within two days. I pull the clasp off of the old knob and replace the knob and the clasp with the new part and it now works great. Thank you for helping me find the part I needed.
Was this helpful?
Thank you for voting!
The original Knob just fell apart
380 of 390 peoplefound this instruction helpful.
Irina from Englewood, NJ
Really Easy
Less than 15 mins
The repair was so easy when I got the part, I did it myself without any help in 5 seconds!
Was this helpful?
Thank you for voting!
washing machine would not go through all cycles or agitate
230 of 294 peoplefound this instruction helpful.
Brian from Millerplace, NY
Easy
15 - 30 mins
After removing frt panel which prys off I checked for anything obvious like a loose belt. Then I jiggled the magnet switch located on the inside of the loading cover. I saw the machine start agitating the it stopped again when I stopped touching it. I ordered the new part and spliced it in with the wire crip tool. Now the machine is A ok.
My Orders
