This lid lock, also known as a door lock, is a genuine OEM replacement part for your washing machine. The lid lock keeps your washer lid closed during the washing cycle. If this part is broken, your w...
Ask our experts a question about this model and we'll get back to you as soon as possible!
10 questions answered by our experts.
< Prev
1
2
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Lorenzo
January 14, 2020
Where can i get an operating manual for this machine?
For model number GTW485ASJ4WS
Hello Lorenzo and thank you for writing.
For your convenience, we have attached the link to your service manual. We hope this helps. Good luck with your repair.
http://media.datatail.com/docs/manual/289313_en.pdf
1 person found this helpful.
Was this helpful?
Thank you for voting!
Tom
June 12, 2023
It seems the sensor to lock the lid is busted..Was wondering if the part "Lid Lock Striker" is the part I need.
Thank you
For model number GTW485ASJ4WS
Hello Tom, thank you for the question. The part you are looking for is the lid switch assembly, part number PS16554755. The lid lock keeps your washer lid closed during the washing cycle. Good luck with your repair!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Kimberly
July 15, 2023
The machine is not agitating, spinning or draining. There isn’t any noise when it’s in those cycles. The control panel is advancing between each mode, but other than filling with water it doesn’t do anything. There is zero noise other than filling and the lid lock. I replaced the lid lock already and it is working properly. Belt is new and in place. The agitator itself still has tension when I spin it, looser one way and tighter the other. Is it possible the motor is bad?
For model number GTW485ASJ4WS
Hello Kimberly, Thank you for writing. We suggest testing the Motor with a Multimeter to check the Ohms to see if it is defective. We hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Billy
September 29, 2023
Spun clothes out went to take clothes out hour later tub had filled half way up
For model number GTW485ASJ4WS
Hello Billy, thank you for reaching out. If the tub of your washer is filling with water, then you may need to check the water inlet valve, part number PS12726769, to fix the issue. The water inlet valve allows water to flow into the washer. If it is not working properly, it may fill the washer with water unnecessarily. We hope this solves your problem!
Was this helpful?
Thank you for voting!
Jean
February 10, 2024
Can not get hot and cold water connections in back of washer back on. They are still leaking.
For model number GTW485ASJ4WS
Hi Jean, thank you for reaching out. We would recommend aligning the water supply lines. Tight the hot and cold water supply lines properly to prevent them from leakage. If the issue persists, we would suggest checking the water inlet valve assembly, part number PS12726769, for any damage. You may need to replace it to fix the issue. We hope this solves your problem!
Was this helpful?
Thank you for voting!
< Prev
1
2
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
Drain all the water out of the tub with a shop vac Remove rear drain hose and drained rest of water into a bucket Remove small rear panel (bottom left hand corner) where the drain hose connects Tipped washer up about 45 degrees to get underneath it - Supported it with a few paint cans Remove internal drain hose/clamps from pump - w/ pliers Remove belt cover (gray plastic) with socket - 3 bolts Remove wire assembly plug from socket Remove old drain pump with socket - 3 bolts Install new drain pump - 3 bolts - plug wire assembly into socket Reinstall belt cover - 3 bolts Reinstall hose to drain pump (note panel will be inside washer) Feed drain hose panel through hole and reinstall - 1 nut Re attached drain hose to exterior drain plug You are done !
Very simple to repair. Be sure to drain the tub outside or into the sump pump then lay the washer on its side. The pump is right there on the bottom of the basket with 3 bolts. You will also need to remove the belt cover to get to the plug. So simple and saves you hundreds off repair man prices.
Turn off hot and cold water supply valves feeding washer. Disconnect both water hoses from washing machine. Remove two screws (one on each side) from upper silver colored metal plate on back of washer to allow access to (blue) water inlet valve. Slightly lift the bottom portion of metal plate and slide to release hooks for easy removal. Pull back and tilt forward plastic control panel to get it out of your way. Disconnect two electrical connections (one on each side) of water inlet valve. One of these came off easily but the other one was stubborn and I had to force it off with a screw driver. If there is an easier way I don't know what it is. Remove two screws from water inlet valve. (one on each side) Gently pull up on stainless steel water temperature sensor located in the middle of the water inlet control valve. It has a black wire connected to it so be careful. Once you have disconnect the sensor you can remove the water inlet valve. If you look closely you will see a small blue O-ring in the hole where you removed the water temp sensor from the water inlet valve. The new valve DOES NOT come with a replacement O-ring so you will have to re-use the old one. I used a small jeweler's screwdriver to get the old out of the hole. Don't forget to install the O-ring or your washer WILL leak! Put everything back together in reverse order. Check hose connections for leaks. Hope this helps somebody. Wish I had known about the O-ring. It would have saved me a headache.