This lid lock, also known as a door lock, is a genuine OEM replacement part for your washing machine. The lid lock keeps your washer lid closed during the washing cycle. If this part is broken, your w...
Ask our experts a question about this model and we'll get back to you as soon as possible!
40 questions answered by our experts.
< Prev
1
2
3
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Kevin
December 30, 2022
what size is this washer machine? 3.8cu or 4.0cu or ?
For model number GTW330ASK0WW
Hello Kevin, thank you for your question. The Washer is 3.8 cubic feet. We hope this helps.
3 people found this helpful.
Was this helpful?
Thank you for voting!
Denise
November 29, 2019
Washer is willing to pump out water but do nothing else. No lights are lit on panel.
For model number GTW330ASK0WW
Hi Denise, the control board is likely faulty and needs replacement. Thank you for your question and good luck with your repair!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Fred
February 1, 2020
Clothes dont spin out
They are very wet
For model number GTW330ASK0WW
Hi Fred. I recommend checking the drive belt part number PS11767488. Thank you for your question and good luck with your repair.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Awilda
December 11, 2019
My GE washer turned itself on and appears to want to agitate....continues to make noise like if it wants to rinse....control panel does not work... i press the button to turn on...but to no avail....
i disconnected it...and connect the plug....and the agitating sound continues....what can i do?????
For model number GTW330ASK0WW
Hello Awilda, thank you for writing. This sounds like the UI & Control Board is faulty. The replacement for your model is part number PS12730586. Good luck with your repair!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Christopher
December 30, 2019
The washer started in the middle of the night by itself. Just the pump is running and won’t stop. Had to unplug it. Checked it in the morning. Can’t stop it and the clothes are still wet. Won’t spin or stop pumping.
For model number GTW330ASK0WW
Hi Christopher, usually this indicates a faulty water level switch. Thank you for your question and good luck with your repair!
1 person found this helpful.
Was this helpful?
Thank you for voting!
< Prev
1
2
3
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
Drain all the water out of the tub with a shop vac Remove rear drain hose and drained rest of water into a bucket Remove small rear panel (bottom left hand corner) where the drain hose connects Tipped washer up about 45 degrees to get underneath it - Supported it with a few paint cans Remove internal drain hose/clamps from pump - w/ pliers Remove belt cover (gray plastic) with socket - 3 bolts Remove wire assembly plug from socket Remove old drain pump with socket - 3 bolts Install new drain pump - 3 bolts - plug wire assembly into socket Reinstall belt cover - 3 bolts Reinstall hose to drain pump (note panel will be inside washer) Feed drain hose panel through hole and reinstall - 1 nut Re attached drain hose to exterior drain plug You are done !
Very simple to repair. Be sure to drain the tub outside or into the sump pump then lay the washer on its side. The pump is right there on the bottom of the basket with 3 bolts. You will also need to remove the belt cover to get to the plug. So simple and saves you hundreds off repair man prices.