GTDP490ED0WS General Electric Dryer - Overview

Diagrams for GTDP490ED0WS

See every part. Know exactly what you need.

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
DRYER FRONT BEARING WHITE 2PK – Part Number: WE03X37318
No Longer Available
DRYER FRONT BEARING WHITE 2PK
★★★★★
★★★★★
(41)
Part #WE03X37318
This authentic, white Drum Bearing Slide, also known as the bearing drum slide, glide, or pad, is a plastic, easy-to-install part for your dryer. It replaces the dryer's front drum slide to allow for easier movement. You'll know if this part is an issue if your dryer is unable to tumble properly or is very noisy. Damage can come from regular use. The part attaches to the outermost side of the bearing. Check both slides for signs of wear, because they often wear at the same rate, and should be replaced at the same time; there are 2 of these particular slides per dryer. This part is sold individually, so you'll need to purchase multiple parts if replacing both at the same time.
DRYER BEARING SLIDE GREEN 2PK – Part Number: WE03X37317
No Longer Available
DRYER BEARING SLIDE GREEN 2PK
★★★★★
★★★★★
(8)
Part #WE03X37317
This original equipment manufacturer Drum Bearing Slide is a plastic, green, easy-to-install part for your dryer. It replaces the dryer's front drum slide to allow for easier movement. You'll know if this part is an issue if your dryer is unable to tumble properly or is very noisy. Damage can come from regular use. As the slides start to break down it may cause your dryer to make noise or not dry clothes in the usual amount of time. You will need to purchase two for both sides of your dryer. They attach to the outer-most sides of the bearing. The manufacturer recommends replacing both slides at the same time. Take this opportunity to clean out the lint and dust in the dryer, to keep it running smoothly. This is a genuine replacement part that comes directly from the manufacturer. This item is sold individually. The part attaches to the outermost side of the bearing. Although this part is denoted as being "Green" in its title, many users and technicians have noted that its true colour is closer to a dark gray or black.
Front Drum Bearing – Part Number: WE3M26
$105.45
Special Order
Front Drum Bearing
★★★★★
★★★★★
(54)
Part #WE3M26
This drum bearing helps your dryer operate as quietly as possible.The drum slides should also be replaced when replacing the drum bearing. The slides are NOT included with this part this is the bearing only. Slides must be ordered separately.
Drive Belt – Part Number: WE03X29897
$49.95
Special Order
Drive Belt
★★★★★
★★★★★
(32)
Part #WE03X29897
This Drive Belt is 89.5" long and comes in black, featuring four ribs on the inside for a better grip. This is a long belt that wraps all the way around the dryer drum, around a tension pulley, and then around the drive motor pulley, allowing all the parts to work together, spinning the drum as the motor rotates. If the drum will not turn when the dryer is turned on the belt is likely broken. It is common for belts to stretch or become brittle over time, which is what leads to the breakage. If broken, it should be replaced; the drum simply cannot spin without this belt. Refer to your model number and user manual to check if this part is right for you. Ensure you use work gloves to protect your hands from sharp internal parts during this repair. Please note: When comparing the length of your old belt to the length of the belt as stated here, remember that a small amount of stretching and contortion may occur with belts over time for a range of different reasons. Unless your belt is drastically different in length, this belt is what you are looking for despite any small inaccuracies. You will need to remove power to your appliance, remove the main panel, and access the motor drive to slip your new belt back into place.
Drum Bearing Sleeve – Part Number: WE1M462
$28.95
Special Order
Drum Bearing Sleeve
★★★★★
★★★★★
(2)
Part #WE1M462
If your dryer’s making loud noises or the drum seems shaky, this rear bearing sleeve might be the fix. It helps the drum spin smoothly and stay in place. When it wears out, you might hear squeaks or notice your clothes aren’t drying as well. Made for GE and Hotpoint dryers, this part is a simple way to get your machine running quietly and efficiently again.
Door Strike – Part Number: WE1X1192
$13.95
Special Order
Door Strike
★★★★★
★★★★★
(3)
Part #WE1X1192
TThe door strike for your dryer is mounted on the dryer frame that the door shuts onto. It fits into the door catch on the door and keeps the door closed. If the door strike is damaged or missing, the door will not lock properly and not only will this cause the door to swing open, but it won’t allow the dryer to start properly. It is a small piece of metal, about 1 inch in length and is sold individually.
Door Latch – Part Number: WE1M1011
$25.31
Special Order
Door Latch
★★★★★
★★★★★
(2)
Part #WE1M1011
This Genuine OEM door latch is designed for use with a wide range of GE clothes dryers. Constructed from a combination of durable metal and plastic, the latch is mounted onto the dryer frame to securely hold the door closed during operation. A properly functioning latch is essential for safe and efficient drying cycles. Sold individually, this replacement part may require a screwdriver and a pair of pliers for removal and installation. Replacing a worn or broken latch helps restore proper door alignment and ensures the appliance operates as intended.
Rear Drum Bearing Kit – Part Number: WE25M40
No Longer Available
Rear Drum Bearing Kit
★★★★★
★★★★★
(2)
Part #WE25M40
This rear drum bearing kit comes with a shaft, bearing and installation instructions. The bearing plate comes with a slot in it for the ground strap. Helps keep your dryer running as smoothly as possible with as little noise as possible. NOTE: Bearing plate has slot in it for ground strap.
Push-to-Start Switch – Part Number: WE4M416
$36.24
Special Order
Push-to-Start Switch
★★★★★
★★★★★
(4)
Part #WE4M416
Restore dependable startup functionality to your dryer with this replacement push-to-start switch, designed to activate the appliance when pressed and released. Compatible with a range of dryer models, this switch is a key component in initiating the drying cycle. If your dryer won’t start or begins running without pressing the button, the switch may be faulty and should be replaced. Installation is straightforward and requires only a Phillips and flathead screwdriver. For safety, always disconnect power before beginning the repair. Once the control panel is removed, the old switch can be disconnected and the new one installed with minimal effort. Sold individually, this part offers a simple and effective solution for getting your dryer back in working order.
High Limit Thermostat - L315-65 – Part Number: WE4M137
$72.70
Special Order
High Limit Thermostat - L315-65
★★★★★
★★★★★
(8)
Part #WE4M137
This part is the replacement high-limit thermostat or safety thermostat for your dryer. The high-limit thermostat is found on the upper right-hand side of the heater housing, and it cuts off power to the dryer motor if the temperature reaches an unsafe level. If you push the start button and nothing happens, the high-limit thermostat should be tested for continuity and replaced if the contacts are open. Be sure to disconnect power to the dryer before you begin this repair. This part is sold individually and is an OEM part.
Door Handle - White – Part Number: WE01X20419
No Longer Available
Door Handle - White
Part #WE01X20419
This part is on the outer door of the dryer.
Light Bulb – Part Number: WE05X20431
$16.96
In Stock
Light Bulb
★★★★★
★★★★★
(3)
Part #WE05X20431
This light bulb is used to illuminate your dryer drum when the door is open. It is sold individually.

Manuals & Care Guides for GTDP490ED0WS

Click to download

Questions And Answers for GTDP490ED0WS

Ask our experts a question about this model and we'll get back to you as soon as possible!

Sort by:
  • 1
  • 2
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Larry - For model number GTDP490ED0WS
December 23, 2019
Dryer hums when we push start button. Does not start.
Chris Boyle Profile
Hello Larry and thank you for writing. If it's the motor buzzing/humming when the start button is pushed then it likely has a bad motor PS11699355. Open the door and manually reach in and rotate the drum in the counterclockwise direction for a couple of complete revolutions and then shut the door and see if the dryer will start. We hope this helps. Please contact us anytime.
$271.51
Special Order
Drive Motor and Pulley
2 people found this instruction helpful.
Was this helpful?
Thank you for voting!
Rocky - For model number GTDP490ED0WS
January 29, 2025
Dryer has Vary loud squeak I opened it up and looked the tensioner looks good belt looks good and tight gliders look warn but not damaged and it ran smooth on the gliders but starts making noises when it gets warm any ideas what part I need to replace?
Chris Boyle Profile
Hello Rocky, Thank you for reaching out. If the Bearing Slides are worn, they should be replaced. As well we suggest checking the Felt Seal and the Read Drum Bearing. Thank you for the inquiry, good luck with the repair!
No Longer Available
Rear Drum Bearing Kit
$18.46
In Stock
Duct Felt Seal
1 person found this instruction helpful.
Was this helpful?
Thank you for voting!
John - For model number PS3654187
July 27, 2025
Timer does not work.
Chris Boyle Profile
Hello John, thank you for reaching out. The timer itself might be faulty. You can try checking the timer for any signs of physical damage or wear. If it's damaged, you may need to replace it. The part number is PS3654187. We hope this solves your problem!
No Longer Available
Dryer Timer
Was this helpful?
Thank you for voting!
Kathy - For model number GE DRYER - MODEL GTDP490GDOWS.
July 20, 2026
when push to start button depressed, dryer turns on and drum turns, but let go and dryer stops. i replaced the push to start button, but the problem still exists. what is next?
Chris Boyle Profile
Hello Kathy, thank you for reaching out. Since you have already replaced the push-to-start switch, we would suggest checking the belt switch next. It can cause this issue if it fails or if the drive belt breaks, which opens the safety circuit. When you release the start button, the open switch cuts power to the motor instantly. You may need to replace it to fix the issue. The part number is PS1481922. We hope this information helps!
$43.00
Special Order
Interlock Switch
Was this helpful?
Thank you for voting!
Jerry - For model number GTDP490ED0WS
July 19, 2021
Timer motor and know have great difficulty advancing the timer cam can it be lubed and with what.
Chris Boyle Profile
Hello Jerry, Thank you for the question. This is normally an indication the Timer Switch is defective and will need to be replaced. We hope this helps!
No Longer Available
Dryer Timer
Was this helpful?
Thank you for voting!
  • 1
  • 2

Common Symptoms of the GTDP490ED0WS

How this model fails, and the parts that fix it.

Watch our pros, then fix it yourself.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Due to over loading of the dryer the drum ruined the slides and was making a bad noise due to plastic rubbing plastic
804 of 916 people found this instruction helpful.
  • Matthew from Plainfield, IL
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
It was pretty easy. After already taking apart the dryer to install a new belt I knew exactly my plan of action. I removed the two screws that hold the top panel of the dryer to the front panel. I then removed the top panel and removed the screws that hold the front to each side panel. I than pulled the front away from the cabinet and drum. I put the new slides in place and installed a new felt strip. I put it back together and that was that. Very easy.
Was this helpful?
Thank you for voting!
Dryer was squeeling when running.
713 of 803 people found this instruction helpful.
  • Daniel from Chicago, IL
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
I removed the two screws at the front above the drum opening (with the dryer door open). The top panel then lifts off. I removed the screw at each side that holds the front panel to the side panels, tilted the front panel forward, which disengages the front of the drum from the front drum glide bearing. I then lifted the front panel sl ightly, unhooking the bottom of the panel from the dryer base, and swung the front panel aside. I removed the existing top drum bearing guide, which was disintegrated, and snapped in the new bearing guide, with the nylon slide strips installed in the bearing guide. Next pulled out the old felt strip, and pressed the new one in place. I then put the bottom of the front panel back into the bottom of the dryer front, and while lifting the drum to asure it fit over the bearing guide, pushed the front panel back to a vertical position to mate with the side panels. I then replaced the side panel screws, replaced the top, and replaced the front top panel screws.
Was this helpful?
Thank you for voting!
Intermittant squeaking noise
631 of 790 people found this instruction helpful.
  • Mark from Addison, IL
  • Easy
  • 15 - 30 mins
  • Screw drivers
Basically, I followed the same steps a prior person posted.
1.Removed the two screws inside the door, on the top part of the opening.
2.Lifted up and removed the top.
3.Removed two screws holding the front panel in place.
4.Held up the drum while removing the front panel. I carefully turned the panel so I could get at the drum bearing without pulling the wires connecting it to the front panel. The wires are not very long, so I had to be careful not to pull on them.
5.Carefully pried off the old drum bearing, using just my hands. It was fairly tight, and popped out just as I started to worry if I was putting too much pressure on it.
6.Checked to see how the old felt was installed, then I pulled out the old felt.
7.Inserted the new felt, being careful to insert one end into a slot the same way the original was installed.
8.Inserted the new slides into the new drum bearing. The gray slides went in at the eleven and one o'clock positions, the white slides went in at ten and two o'clock.
9.Removed a surplus plastic piece from the new drum bearing (where the light comes through).
10.Inserted the new drum bearing, putting the bottom tabs in first, then pivoting it into place. I squeezed it into place to make sure it was tight.
11.Lifted up the drum and put the front panel back on.
12.Screwed the front panel back on, using the two screws.
13.Carefully put the top back on.
14.Screwed in the two screws inside the front door to fasten down the top.
That was it! I started up the dryer and it worked fine. No more squeaking.
About the only thing odd about the repair is why PartSelect sells each slide separately (i.e., I had to order 2 white slides and 2 gray slides). I can't imagine replacing just one, so why not package them in pairs, or maybe even all four in one package.
At any rate, the repair was easy, and a lot cheaper than having someone come out to fix it.
Was this helpful?
Thank you for voting!