GTD42EAAJ0WW General Electric Dryer - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Lint filter tore
-
Lisha|Lamb from SHELDON, MO
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
32 of 34 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
interlock switch was bad. Prevents the dishwasher form running as it "thinks" the door is still open.
Opened door, removed screw holding down metal plate that presses against interlock switch when door is closed. Removed plastic cover thingy that is over interlock switches. Removed the interlock switch by pressing the plastic lock thingy away from switch. Pulled the wires off each end of the interlock switch. Removed new interlock switch from plastic bag and reversed above procedure. Done, shut door and the dishwasher works.
Parts Used:
-
Steven from EPHRATA, WA
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
31 of 51 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Broken/ Tore Lint Filter
Opened dryer door and pulled out and Removed Broken old Lint Filter, inserted New Lint Filter into Lint Filter slot, then closed Dryer door.
Parts Used:
-
Cristina from WHITTIER, CA
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
17 of 18 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The light bulb in the dryer burned out
The repair, from the time that the bulb burned out until it was replaced took about six months. I could have shortened the time if I had ordered the bulb sooner. It was difficult because I had to listen to a fair amount of nagging, which, thankfully, has now ceased. I also had to actually go online and finI opened the dryer door, reached in with my right hand (which happened to be holding the new bulb) and screwed the new bulb in. Tip: Screw it in counter-clock wise. This was not mentioned in the instructions. Come to think of it, no instructions were provided. The company might wish to correct that oversight.
Parts Used:
-
Colin C. from GENEVA, IL
-
Difficulty Level:Very Difficult
-
Total Repair Time:More than 2 hours
11 of 11 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
blub burned out.
I first throwed the breaker then I took the old bulb out. Put new bulb in. Turned the breaker back on.
It worked great
It worked great
Parts Used:
-
Mary from Oak Point, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
14 of 20 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
needed new lint filter
-
Aaron from MERIDIAN, ID
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
11 of 13 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
dryer would not stay on so I ordered a button, but wrong part.
First I called to get help with the right part and they told me I needed the pus-to-start-switch. It came in and I called my handyman Ed to install it. I am happy with your service. I dont install but just got the part in.
Parts Used:
-
Linda from FITCHBURG, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:1- 2 hours
16 of 29 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer would not start
I popped the door switch out with a small screwdriver, disconnected the electrical connection and re-connected the new switch and popped the new switch in place with a little adjustment.
Parts Used:
-
Kenneth from COATESVILLE, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
10 of 12 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer wouldnt work
Dryer wouldnt work. I was out of town when dryer stopped working. My grandmaother, who I live with, had brother came over to troubleshoot. He spent a good amount of time and couldnt figure out the problem.
When I returned home I tried it and immediately knew the knob was stripped because it didnt make the clicking noises. I verified by seeing where flat section was, then turning with knob and then seeing if flat section moved. Ordered new knob. Pulled old one off and put new one. Worked like a charm
When I returned home I tried it and immediately knew the knob was stripped because it didnt make the clicking noises. I verified by seeing where flat section was, then turning with knob and then seeing if flat section moved. Ordered new knob. Pulled old one off and put new one. Worked like a charm
Parts Used:
-
Alicia from METAIRIE, LA
-
Difficulty Level:Very Easy
-
Total Repair Time:30 - 60 mins
10 of 12 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dishwasher would not turn on.
There are 2 switches that should be pressed in when you move the handle to lock door, the switches usually go bad with time. Just take the six screws off on the inside of door, then remove screw on the underneath part of handle. The switches are located on the top part under a piece of 1 inch metal plate held in by a screw, remove that and you'll see the 2 switches, test the button on each one to see if it goes in and out, you'll hear the click to. Just unplug bottom first then the top if you need to replace the top one. Thats it.
Parts Used:
-
Patrick from QUINTON, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
9 of 9 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burned out interior dryer drum light
Tried to replace with home-store bought 6w light. Looked the same, fit into socket, but didn't work. Actually exploded when I turned it on! Be sure to use OEM part like this one. Worked perfectly!
Parts Used:
-
David from Plymouth, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
11 of 18 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer was making noise
Took the top and front end of the dryer off. Took the old slider spacers off and installed the new ones. I replaced all four of them even though only two was bad. While I had the dryer open I decided to use my shop vac to clean up the lint that had accumulated there. Replaced the front and the lid plugged it up, hit the start no noise just like new.
Parts Used:
-
Maurice from MINERAL SPGS, AR
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
8 of 10 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The old filter had holes in it
-
Robin from CANTON, OH
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
7 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lint Filter Frayed
-
Margarita from AUSTIN, TX
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
7 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
DRYER WOULDN'T START
My dryer knob broke on the timer cycle switch so I ordered a new one along with a new dryer knob which didn't fix the problem, then I ordered the start switch and all I had to do was remove the back of the dryer where all the knobs are located and remove the start switch by turning the start switch to remove it, replace it with the new one by turning it till it clicks in just like when you removed it, put knob back on the front. However that didn't fix my dryer either so I ordered the thermal fuse and switched it out and that was what started the dryer back up. It is located on the back all the way to the bottom where the electrical cord is. Remove the cover and locate the fuse. Use a pair of pliers to pop it out and push the new one back in.
Parts Used:
-
GLENDA from BLNG SPG LKS, NC
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
8 of 13 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!