GSHF3KGXGCCC General Electric Refrigerator - Overview

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Refrigerator Ice and Water Filter – Part Number: MWFP
$94.45
Special Order
Refrigerator Ice and Water Filter
★★★★★
★★★★★
(19)
Part #MWFP
This ice and water filter helps reduce impurities in select side by side and bottom freezer refrigerators. Replace it about every six months, or when water flow slows, ice production drops, or the filter light turns red. Some older filter setups may need an adapter. Place a cloth under the filter before removal. Check the exact refrigerator model before ordering.
Temperature Sensor – Part Number: WR55X10025
$34.68
Special Order
Temperature Sensor
★★★★★
★★★★★
(10)
Part #WR55X10025
Also known as a thermistor. This part is used to sense the temperature in the cabinet.
Module Shelf Insert - Clear – Part Number: WR71X10761
$64.23
Special Order
Module Shelf Insert - Clear
★★★★★
★★★★★
(13)
Part #WR71X10761
The Module Shelf Insert is a complete assembly for the module shelf. This repair is rated as "Easy" by users. Simply remove the old shelf insert and snap the new one into place using the locking tabs. This part is used to hold items in the fridge, and if broken it should be replaced. Refer to your user manual and model number to ensure this part is right for you.
Union Connector - 5/16 Inch to 5/16 Inch – Part Number: WR02X11330
$23.79
Special Order
Union Connector - 5/16 Inch to 5/16 Inch
★★★★★
★★★★★
(1)
Part #WR02X11330
Quick connector for plastic water line - 5/16" to 5/16"
Main Control Board Assembly – Part Number: WR55X10942C
No Longer Available
Main Control Board Assembly
Part #WR55X10942C
This electronic board (Main Control Board Assembly, Control Board, Motherboard) controls the temperature and defrost functions of the unit. This control board is located on the back of the refrigerator, and measures 8 inches by 5 inches. It’s constructed of metal and plastic, and comes in green. This kit includes one main control board with built in defrost controls. If broken due to electrical surges or normal use, your fridge may experience temperatures that are too warm or too cold, or inconsistent defrost cycles. If this happens, the part should be replaced.
Water Tank Assembly – Part Number: WR17X11440
$59.40
Special Order
Water Tank Assembly
★★★★★
★★★★★
(32)
Part #WR17X11440
This tank stores water until the water actuator is activated and water is requested.
WATER VALVE WITH GUARD – Part Number: WR57X33326
No Longer Available
WATER VALVE WITH GUARD
★★★★★
★★★★★
(8)
Part #WR57X33326
This double inlet water valve has quick connections. This valve has 1/4 and 5/16 John Guest fittings for the outlet lines and a 1/4 compression fitting for the inlet line.
Defrost Heater Harness Kit – Part Number: WR51X10101
$155.93
Special Order
Defrost Heater Harness Kit
★★★★★
★★★★★
(3)
Part #WR51X10101
This dual heater kit replaces the single heater. It's redesigned to use two heating elements for a better defrost cycle.
Evaporator Fan Grommet - Red – Part Number: WR02X12008
$16.74
Special Order
Evaporator Fan Grommet - Red
★★★★★
★★★★★
(5)
Part #WR02X12008
This evaporator fan grommet is red in color, and is about 1 inch in diameter.
Light Bulb - 40W – Part Number: 40A15
$19.10
Special Order
Light Bulb - 40W
★★★★★
★★★★★
(3)
Part #40A15
This 40-Watt light bulb is sold individually. It is specially designed to withstand extreme temperatures, so this bulb is compatible with a variety of appliance types including refrigerators, ranges, microwaves, and dryers. It features a frosted glass bulb with a standard metal socket base, which allows you to easily unscrew the burnt-out light and twist the new bulb into place.
BUCKET AUGER – Part Number: WR29X43990
No Longer Available
BUCKET AUGER
★★★★★
★★★★★
(12)
Part #WR29X43990
When activated, the auger rotates and pushes ice out of the bin through the chute to the user.
Compression Ring – Part Number: WR02X12149
$13.95
Special Order
Compression Ring
Part #WR02X12149

Manuals & Care Guides for GSHF3KGXGCCC

Click to download

Common Symptoms of the GSHF3KGXGCCC

How this model fails, and the parts that fix it.

Watch our pros, then fix it yourself.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Refrigertor water dispenser not working BUT ice machine is working
1038 of 1163 people found this instruction helpful.
  • ralph from bristow, VA
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers, Socket set
The very first symptom here is important! The door water dispenser is not working but the ice macine is working. You may only have a frozen water tube in the door so do the following before diagnosing that your solenoid valve is bad: 1) the tube usually runs under the front of the refrigerator and usually has a quick disconnect. Undo t he connection and press the dispenser. If water comes out of the tube you have a frozen or blocked tube in the door. 2) Immediately adjust the temperature in the freezer and warm the freezer compartment as much as you can without destroying the freezer contents. Wait 24 hours. This will usually unfreeze the line. Do not waste your time with a hair dryer. NOW, if this doesn't work and you are convinced you need to order and replace the solenoid, follow these steps. Assemble your tools first. I needed a good ratchet set and a screwdriver. A shop towel is helpful for spilled water. A light is handy. Pull out the refreigerator to gain access to the rear of the unit. Unplug the power and close the water valve (older homes, you may need to actually shut the house water supply). Remove the screws which hold the cover over the lower half of the refrigerator. On the left you will see the solenoid. It's always good to see that your new part matches the one you feel needs replaced. They may not match perfectly due to changing design but they should be very similar. One screw holds this part in place and access is very simple. Now simply unplug the electrical connections. In my case, one blue "blade" type connection (powering the water) and one red "blade" type connection powering the ice maker. They are not the same size and this coupled with the coloring means you will not accidently switch them. pull the tubes clear of the solenoid. This is simple and needs no explantion. Grab your new solenoid and reattach both the electrical and water lines (two, remember, ice maker and drink dispencer). Replace the single screw. Re-attach the rear, lower refrigerator cover and go to the front of the unit to check the water. You can listen carefully and hear the power engage from the new part bringing you water. Clean up, replace the refrigerator back to its place and look really tired when your wife sees that you worked "so hard"! You probably saved at least $50-$80 from a service call which can now be used to take the family to dinner after your "exhausting" 15 minute workout of removing about 10 screws and wheeling the unit in and out of place. Writing this article took longer! My 4 year old worked harder holding the flash light!
Was this helpful?
Thank you for voting!
Plastic Auger blades broke in ice tray
586 of 630 people found this instruction helpful.
  • Tim from Newport News, VA
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Screw drivers
I used a digital camera and photographed the assembled unit and the metal blades before I started the repair. Then, I removed the top screw on the clear shield. Flip over ice tray and removed two Phillips screws on bottom. Exterior plastic white cover comes off next. The cover sides have hard push-in white plastic tabs. Push them in; pry up top cover with small flathead screwdriver. Slide white top cover up and you will now see the metal blades and assembly. Auger is held in place with a metal c-clip and washer on the end. Use flat head screwdriver to pry off c-clip. Then you will see a nylon round slotted nut. The threads are reverse, use pliers and loosen nut. It is not that tight but pliers are needed. Then it all is loose and ready for removal. I slid all the blades off at one time and kept them stacked together. Slide out auger and clear flat shield cover. Install new auger, clear shield, and metal blade stack. When you put it all back together take a look at the long metal J-hook on the bottom make sure it is in the slot before you make everything tight. Failing to do this will prevent cubed ice from dispensing.
It is not that hard to do the repair it just takes some patience and paying attention to details.
Was this helpful?
Thank you for voting!
Fridge too warm, evaporator icing up
606 of 738 people found this instruction helpful.
  • Gerald from San Clemente, CA
  • Easy
  • 15 - 30 mins
  • Screw drivers
After replacing the defrost heater, main board and thermistor I still had the same problem. Called a repair guy and he (with the help of GE on the phone) diagnosed that the temperature sensor was bad. So I ordered from partselect and installed it and it fixed the problem. Been good for a couple months (knocking on wood). To install I had to cut the 2 wires to the old sensor, crimp the 2 new wires on and snap the new sensor to the clip on the evaporator. Very easy. Make sure you seal the ends of the wire crimps so moisture doesn't get in and corrode the connection.
Was this helpful?
Thank you for voting!