Your washer uses 4 tub dampening straps. It is recommended to replace all 4 at the same time. They keep the tub in the center of the cabinet and are sold individually.
The main tub seal is located between the transmission and the outer tub. It's the primary water seal in the outer tub for the transmission-shaft. This seal is difficult to replace and should probably ...
This tub bearing goes in your washing machine. You will find it on the bottom of the outer tub, where the transmission goes through the tub. If you hear metal on metal when the washer is spinning, you...
This timer dial with compression ring shows you which part of the cycle your washer is in. It is white in color and can be found mounted on the timer shaft. You may need to replace this part if your ...
This drive belt is made to slip on the motor pulley to bring the basket up to the speed required and this makes the belt get wear and tear.
$45.99
Special Order
Questions And Answers for GNSR3150H1WW
Ask our experts a question about this model and we'll get back to you as soon as possible!
2 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Scott
October 5, 2022
The knob does not engage to allow me to select the desired cycle. It just spends freely. I can select my cycle by physically turning the cycle ring. This is hard to do. It seems that the outside knob won't engage to do it. I'm wondering what part(s) are required to fix this. The washer works fine otherwise.
For model number GNSR3150H1WW
Hi Scott, thank you for contacting us. We have researched your model and found that the issue is probably with the knob, part number PS1482286. We would also recommend checking the timer knob clip, part number PS270835, if it engages properly. If you require assistance to place an order, please contact customer service. We hope that helps!
Ma machine à laver ne brasse pas,elle se remplie et se vide mais ne brasse pas. pouvez vous me donner un conseil? Je vous ai acheté la switch mais ça ne fonctionne pas plus
For model number GNSR3150H1WW
Bonjour Doris, Merci pour la question. Si la laveuse ne s'agite pas, nous vous suggérons de vérifier l'usure ou les dommages de la courroie et de l'accouplement de l'agitateur. Nous espérons que cela vous aidera !
I spoke to a very nice young ladie who took my order and I received my order within two days. I pull the clasp off of the old knob and replace the knob and the clasp with the new part and it now works great. Thank you for helping me find the part I needed.
1. Drained the wash tub by taking the drain hose from the back of the washing machine and dropping it below the tub - water flowed out of hose a lot easier than trying to suck water out of tub using a pump (tried this on the first time I tried to fix washer). (Washing machine on 2nd floor of house and didn't want water running on floor) 2. Removed the 2 bolts holding the Pump/Motor assembly to the machine. 3. Removed both hose clamps on the Pump/Motor assembly and removed Pump. 4. Attached the new drain inlet hose to the pump and then to the tub with the original hose clamps. 5. Attached the drain hose to the pump and then plugged in the 2 wires for the pump. 6. Plugged in the washing machine and everything worked.
NOTES: 1. Hardest part was working with hose clamps (spring type clamps) in the tight space under the machine. 2. Easier to fix since I pulled machine apart a few days before - removing the clog in the pump/motor assembly only to get everything back together to find out that the motor was dead. Still well worth the time and effort due to not having to go out and buy a new Machine...