The door strike on your washing machine allows your washer door to lock properly, and operate efficiently. If you notice that your washer door will not open or close, leaks or the washer will not star...
$19.58
In Stock
Order within the next 7 hrs and your part ships today!
This kit is used for front load washers and includes 2 dual-stage shock absorbers, 1 spare shock mounting pin and 4 locking nuts. These shock absorbers keep the washer from vigorous shaking during it's cycles.
$50.58
In Stock
Order within the next 7 hrs and your part ships today!
This door lock and switch assembly is manufactured to lock the door on your front load washer to prevent it from opening while it is running. You may need to replace the door lock and switch if the do...
$163.10
In Stock
Order within the next 7 hrs and your part ships today!
The pump is what your washer uses to remove the water from the tub. This part is the pump and motor assembly which includes the red flapper to prevent drain back flow.
$211.11
In Stock
Order within the next 7 hrs and your part ships today!
Also known as a Door Boot Seal and is used in front load washers. This part is used to keep the clothes inside the tub during the wash cycle. The folds in the bellow allow the tub to move separately f...
$393.85
In Stock
Order within the next 7 hrs and your part ships today!
This is a replacement screw for your washer or dryer. The screw is approximately half an inch in length and is a Phillips-head screw. It screws in from the outside of the drum, into the vane/baffle. T...
$16.47
In Stock
Order within the next 7 hrs and your part ships today!
Order within the next 7 hrs and your part ships today!
Questions And Answers for GLTF2940ES1
Ask our experts a question about this model and we'll get back to you as soon as possible!
2 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Al
March 10, 2020
Washer works, but will not spin dry
For model number GLTF2940ES1
Hello Al, thank you for your question. The first parts we would recommend testing/replacing would be the door switch Front Load Washer Door Lock and Switch Assembly Part Number: 131763256, and the Drive Belt Part Number: 134051003. If those parts are ok, the issue could be the motor control board. I hope this helps.
Was this helpful?
Thank you for voting!
Bob
January 22, 2023
When I press the start button the water starts to fill but the unit will not agitate. The timer will not countdown either. No error code appears
For model number GLTF2940ES1
Hello Bob, Thank you for your inquiry. The most common causes of this issue are a faulty door lock switch, an issue with the drive belt, a faulty drive motor, or an issue with the suspension springs and shock absorbers. You can check the switch and motor with a multimeter and check the springs and shock absorbers for any visible damage. If you are unfamiliar with how a multimeter functions, we have videos available to assist you. We hope this helps with your repair.
This was one of the simpliest repairs I have ever done taking less than 5 minutes to complete. On the inner door I removed the two screws that hold the plastic catch in place. I then removed the broken catch and put the new catch in place. Finally I replaced the two screws that hold the catch in place and it was done.
1. Unplug unit. 2. Unscrew 2 nuts holding top in place in rear of unit using phillips head screwdriver. 3.Slide top back and remove. 4. Open door of washer and unscrew 2 screws holding in door lock unit. 5.Pull out unit from the top and install new unit reconnecting the 3 wire connections.
remove top of machine by removing 3 screws along the top edge in the back of your machine and then sliding the top back and up. Then loosen the screws holding on the control panel enough to get to the 2 screws at the top of the door panel. Next remove bottom panel by removing 2 screws along bottom edge then pulling it free from snaps. Then along the outside lip of the bellow, just inside the door, is a wire clip that is easily removed by prying it past rubber lip with a screw driver and lifting it away. Remove the door panel by removing the 2 screws you exposed by loosening the control panel and 2 more along the bottom that were exposed when removing bottom panel. After the door panel is removed and the bellow is completely exposed, you will find that it is held in place by a circular spring which wraps the whole way around the drum opening. Again it can be removed by prying it out away from the groove in which it sits with a screw driver. Now your machine is broken down as far as it needs to be. From here you can follow the directions included in your new bellow kit and put it back together by following these instructions in reverse.