This is the replacement water inlet pipe or water inlet valve for your washer. It is made of white plastic and is approximately 8.5 inches by 3 inches, with an opening diameter of approximately 2.5 in...
This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time. This pump has sound isolation mounting washers and a filter.
This is the replacement water valve for your washer. It has 2 inlets and 3 outlets. The water valve connects to the water source and solenoid wires, and ensures the tub has the right amount of water e...
Ask our experts a question about this model and we'll get back to you as soon as possible!
6 questions answered by our experts.
< Prev
1
2
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Setrean
March 7, 2020
What part do i need to buy to replace the rubber on the part of the washer that is visible when you open the washer ? A piece is ripped off and now the washer is leaking
For model number GFWN1100L3WW
Hello, Thank you for contacting us. I have researched the model you have provided and have found the part you are looking for is Door Gasket - Part# PS3417678.
Washer stops before rinse/spin. It will rinse and spin by setting at that mark again
For model number GFWN1100L3WW
Good Day Sally. Thank you for your question in regards to your unit (Model Number GFWN1100L3WW). Based on our research, this could be the result of a faulty door strike (Manufacturer Part Number WH01X10356). This part has been discontinued and we no longer have any remaining left in our inventory. If this is the reason why you are having this issue, we would recommend reaching out to the manufacturer as they may be able to recommend an alternative part that is compatible with your unit. It may also be something to do with the Drive Belt (PartSelect Number PS3487271), or the Motor and Drain Pump (PartSelect Number PS1766031). You can order these parts either online at our website www.PartSelect.com or by calling us by phone at 888-260-4310. Best Regards.
Was this helpful?
Thank you for voting!
Adesh
February 8, 2020
Washer drum does not rotate, what can be the reason
For model number GFWN1100L3WW
Hello Adesh,
Thank you for your question. Our source suggest replacing the drive pulley kit under part PS1016963 for your model to fix the issues. We hope this helps.
My GE washer model gfwn1100l3ww leaves the lid light on and does not change wash cycles?
For model number GFWN1100L3WW
Hello Raul, Thank you for the question. This is normally an indication the Door Lock Latch, PartSelect Number PS1021459 is defective and will need to be replaced. We hope this helps.
Hi Raul,
Thank you for your question. For operating instructions for your washer, you will need to consult your owner's manual. Here is a link where you may view your owner's manual, https://products.geappliances.com/MarketingObjectRetrieval/Dispatcher?RequestType=PDF&Name=49-90454-2.pdf. We hope this helps. Thank you and have a great day.
Was this helpful?
Thank you for voting!
< Prev
1
2
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
Remove the front coverfrom the machine. This is done by removing the 3 screws at the bottom of the panel. The panel then drops down and pulls straight off. The pump is located on the front right wall of the of the machine. You will notice a 2-3 inch diamete threaded cap on the right side of the front wall of the machine. This is the front of the pump and access to the filter. Place a large bucket under this cap and slowly loosen the cap. All of the water remaining in the machine will begin to drain (this could be a lot of water. Do not remove the cap completely so that you can quickly stop the flow of water if needed). Once all water is drained from the appliance, Disconnect the two hoses from the pump using a pair of pliers to looses the presure clamps, sliding the clamps back an then pulling off the hoses (be careful of any remaining water in the hoses). Then remove the two screws from the rear base of the pump that secure it to the bottom floor panel of the washer. Slide the pump slightly to the rear to free it from the fittings on the front wall of the machine and the lift the pump up. At this point, firmly pull out the wiring harness plugged into the top right side of the pump. Install the new pump by plugging in the wiring harness and resecuring the pump. Plug in the machine and run on the rinse and spin cycle to test.
I took the two drain hoses off with the pliers then only two screws that holds the pump. After that the two hot wires which are black and white. But remember to unplug you're washer since the pump is not grounded you don't want to risk being shocked. Hope thi helps. Plus i saved around 250.00 by repairing myself.
I called a repair person to check my 15 months old GE front loader washer that stopped in rinse mode. After his inspection he said it was a deffected computer board and it would be very expensive to replace the 3 computers boards inside and it would be cheaper to buy a new top loader washer. The next day I lifted the top cover and found a taped plastic envelope with instructions titled “For service Technicians Only." On page 2, instruction on to how to enter the washer in to service mode and to test the washer: Press : Signal, Delay, Signal, Delay (within 30 seconds of plug in washer) Then rotate main knob to #102 and press Start:(the washer did a test for finding the problem) , and for me was : E22 , it means : replace solenoid valve assembly. So I order the part from Partselect.com for $58.00 and my Washer runs beautiful, thanks to the instructions inside.