This is a flood switch assembly for your washer. The flood switch controls the hot and cold water filling your washer tub to ensure the proper amount of water. You may need to replace this part if you...
This is an end cap for a dishwasher rack. This part is about 2.5 inches long, is black, and is made of plastic. You may need to replaced this part if it is broken, or if your dishwasher rack continuou...
This is replacement door latch for your dishwasher. The door latch is attached to the tub frame, and connects to the door strike to keep your dishwasher door closed during operation. If you have a bro...
This drain pump kit is for dishwashers. The drain pump kit removes the water from the dishwasher tub during the drain phase of the dishwashing cycle. The kit may include multiple parts; refer to your ...
This is a genuine GE dishwasher leveling screw. It operates as a leg on the bottom of your dishwasher, and can be screwed in and out to raise and lower the height of the dishwasher. It is made of meta...
This is a lower rack roller for your dishwasher. It attaches in the lower roller assembly on the bottom of your rack to allow the rack to smoothly slide in and out. This replacement part is 1.5 inches...
Ask our experts a question about this model and we'll get back to you as soon as possible!
5 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Bruno
December 26, 2019
I have power but do not start when i push start then a blink light in the front panel and nothing happen
For model number GDT545PSJ2SS
Hi Bruno, thank you for your question. You may want to take a look at your door latch. If that part is not registering that the door is shut then your appliance will not start. If that part is fine you may need to look at your flood switch. However if both those parts are working then the issue may be in your control board. Good luck with your repair.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Jack
February 21, 2020
I have read quite a bit of literature for the troubleshooting on this dishwasher, can’t seem to solve the problem. Lights just keep blinking. I’ve shut it off several times and restarted it but no luck. Am i missing something? Thanks
For model number GDT545PSJ2SS
Hi Jack,
Thank you for your question. The blinking lights may indicate a problem with the dishwasher caused by power surges. If you have tried resetting it and you have also unplugged the dishwasher and plugged it back in and this has not resolved the issue, there may be some other issue going on in the dishwasher. There are some parts that you will need to check to see which one is causing the issue. You will need to check the heating element, the drain pump and the touchpad and control panel. You should also find a tech sheet just behind the access panel of your dishwasher that will help you run some diagnostic tests. If checking these parts and running the tests do not help, you will need to have a technician check your dishwasher. We hope this helps. Thank you and have a great day.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Brian
January 13, 2022
Dishwasher chimes often and sometimes doesn't start without flipping a power breaker
For model number GDT545PSJ2SS
Hello Brain, thank you for your question. You will have to put the dishwasher into diagnostic mode to check the error codes. To do this you can only enter the diagnostic mode from the Error Code Display Mode’. Once you have verified that it is in Error Mode, press and hold down “Cycle Start” for about five seconds (this activates the tests). It is important to note that you Press “Cycle Select” each time you want to select/Increment to the next Test (and you press Start to either Start/Stop a test). When the test is finished a specific LED illuminates to indicate the error condition that is present. We hope this helps.
Was this helpful?
Thank you for voting!
William
August 8, 2022
When you hit the start button, the machine chimes 3 times and does nothing. There is no error code on this machine that I can find.
For model number GDT545PSJ2SS
Hello William, Thank you for the question. The dishwasher may be in demo mode. To exit demo mode, hold “START” and “HEATED DRY” at the same time for 5 seconds. We hope this helps!
Was this helpful?
Thank you for voting!
Bob
January 28, 2020
Dishwasher seems to not be getting any power. I have checked circuit breakers, etc. No problem there. None of the display lights are on. Again, it is acting like there is no power.
For model number GDT545PSJ2SS
Hi Bob, thank you for your question. You may want to take a look at your door latch for being the issue. If that part is fine then the issue might be in your control board. Good luck with your repair.
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
Took off the kickplate, diconnected the wires and removed the whole door by lifting straight up, removing spring wires from hinges. Once door is disconnected from the machine, removed one hinge by removing bolt. Slid gasket into place, secured hinge back in place, then reconnected wires at bottom, replaced hinge spring wires and slid door back down onto hinges. Now that we know how to do it, could do it in 15 min to half hour.
We tried cleaning out the filter and it clogged with a huge amount of gunk. We removed the gunk, scrubbed the filter, and tried running the dishwasher, but still no water. That took over an hour (not counting the time the dishwasher spent running). Then we tried your diagnosis center and it pointed to the flood switch or the water valve. I extracted the flood switch (another 30-60 minutes) to check it, and it also contained gunk and (significantly) did not rattle, which made me suspect the flood switch was the problem, so I ordered one. Once the replacement arrived, I checked it and the flood switch rattled, confirming that it should work properly. I spent 30-45 minutes installing it, plus the filter assembly and racks I had to remove to access it. Ran the dishwasher and everything came out sparkling clean. I don't know where the gunk came from, but if you aren't getting water and the filter is full of gunk, check the flood switch.
1. Turn off breaker supplying power to dishwasher in electrical panel 2. Open dishwasher door 3. Unscrew the screws that secure the dishwasher to the counter. 4. Tip dishwasher forward. Identify the non-functioning door latch. It looks exactly like the replacement. Unclip the wire harness from the door latch. 5. On the inside of the dishwasher, there are 2 screws directly under the door latch. Unscrew them and carefully set aside. 6. Remove old door latch. 7. Set new door latch in place. Holding securely, replace screws removed in step 5. Toward the end they get a little tougher to screw in. 8. Plug wire harness into new door latch. 9. Re-align dishwasher and re-secure to counter in previous position. 10. Test latch to make sure it closes properly. 11. Turn on breaker in electrical panel. The dishwasher should now function properly.