This part is the replacement drawer slide rail for your refrigerator. The crisper draw will slide in and out along this rail. If the rail is damaged or missing, the crisper will either hang from one s...
This is a replacement evaporator fan grommet for your refrigerator. The fan grommet absorbs the vibration from the evaporator fan motor for quiet operation while it runs. If your evaporator fan is unu...
The lid bumper or evaporator fan motor bumper in your refrigerator prevents the fan motor from scraping against the side bracket. If your refrigerator/freezer is noisy, the bumper could be worn down o...
This is a 12-24 TT HX 7/8 S refrigerator or freezer screw. It is a little over 1 inch in total length. This is sourced directly from the original manufacturer.
This part helps the compressor kick on and off while maintaining a constant temperature to keep things frozen in your freezer. This part has been updated by the manufacturer and may appear different t...
This evaporator fan blade is for your refrigerator, and it circulates air so that the temperature of the fridge is regulated. This model has 3 blades, and is a little more than 4 inches in diameter. I...
No Longer Available
Questions And Answers for GBRS0HBXCRSS
Ask our experts a question about this model and we'll get back to you as soon as possible!
3 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Karen
December 20, 2021
My fridge section is not cooling however the freezer is working fine
For model number GBRS0HBXCRSS
Hello Karen, Thank you for your inquiry. The damper is what allows the cold air from the freezer into the fridge. At the same time, you still want to check the evaporator fan motor as it could be keeping the freezer cold, but not strong enough to allow the air into the fridge. We have researched the model you have provided and we would recommend checking the following parts to fix your issue: the damper and eps assembly, the damper duct, the evaporator fan motor, and the control board. You can test the parts with a multimeter. Good Luck with your repair.
I want to reverse the door swing but don't have the required attachment. Is there a number I can order?
Thanks
For model number GBRS0HBXCRSS
Hi Mimi, thank you for contacting us. The compatible door-reversing hinge kit for your model is part number PS2340396. This kit is used to reverse the door swing. Please reach out to customer service if you need help placing an order, anyone will be happy to assist you!
Hello Fred, thank you for asking. Based on the description you have provided, we would recommend checking the control board, part number PS2340426, to fix the issue. We hope this helps!
I have a fridge in my garage. I have found that a glass of ice water or a cold drink outside is very important to me. When I discovered melting ice dripping onto the garage floor I was very upset. I spun the fridge and found that the compressor and fan weren't starting. I got out my multi-meter and discovered that power was not making it to these components. I did some research and found the wiring diagram online. There really isn't too much going on with a fridge and the most likely candidate seemed to be the run capacitor. I ordered the part, replaced it in a few minutes and the fridge began working again.
I applied some tips learned by reading other reviews. So before I started I grabbed my trusty vise grip pliers and a small screw driver. I locked onto the switch actuator, the part that the refrigerator door pushes in, with the vise grips and pulled on it just hard enough to get the screw driver inserted in the right side to push in the catch clip so the switch could be pulled out further each time the catch clip was depressed to the next detent. Then I used the screw driver on the left site to encourage the switch past the detents on the left and very quickly the switch was out of the mount. The wires from the refrigerator pulled out with the old switch. I unplugged the old switch from the wires and plugged in the new switch and shoved the new switch back into the mount, wiggled it a couple of times to make sure it was secure and the job was done. Once I applied the vise gripes at first, the whole job took less than a minute.
unplugged refrigerator. removed light bulb from old socket. unsnapped old light socket and pulled it out just enough to diconnect the electrical plug that plugs into the socket . discarded the old socket and plugged in new socket. snapped in new socket into refrigerator. i watched how to do this simple procedure on you tube and decided to do it myself. easy easy easy