This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
Glass ONLY. This inner door glass is a heat resistant part that fits into a stove, oven, wall oven, cooktop, or range as the inner glass panel of the appliance door.
This oven rack is chrome in color and is approximately 24.76 inches wide by 15.78 inches deep. If your old oven rack is damaged, you should consider replacing it. Many of our customers have determined...
This is a replacement light bulb to illuminate the inside of your oven. It is 25 watts and 120 volts. Please wear gloves during replacement if your existing bulb is shattered. Consider ordering a spar...
This part is the replacement door gasket for your oven. It is made of gray rubber and is sold individually. The door gasket runs along the circumference of the oven door and creates a seal that insula...
Ask our experts a question about this model and we'll get back to you as soon as possible!
1 question answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Gerald Allen
February 5, 2020
Turns on starts to heat up then turns off and lights go out. I’ve reset the clock several times now, i’ve turned off at breaker to reset. It starts over nicely but continues to shut down after only a few minutes.
For model number GBD309PVS02
Hello Gerald, thank you for your question. We would recommend testing the thermostat and sensor which is Range High-Limit Thermostat PartSelect Number: PS11747248, Temperature Sensor PartSelect Number: PS11748765, first. The thermostat establishes and maintains the internal temperature of the oven cavity and the sensor detects the temperature within the oven cavity. These parts can cause the unit to stop heating. If those parts are ok, the issue could be with the electronic oven control board. I hope this helps.
Easily removed the door from the oven by releasing clips attached to the door hinge -- very nicely engineered. Removed about 6 philips head screws to allow the door assembly to be taken apart for access to the glass. Lifted out the broken glass, cleaned the inside of the door, installed the new glass, reassembled the door (a two minute project), and reattached the door to the oven. Cleaning the inside of the door took longer than the actual repair!
Something Kitchen Aid wont tell you but running a self clean on this model stove blows the fuse located on the back of the stove.
First I slid the stove out and removed the back of the stove held in place by 8 Phillips screws. The thermostat fuse is located near the top middle on the back of the stove. Remove the 2 screws holding it in place. Disconnect the wires, plug in the new part. Put it all back together. Job done in less than 30 minutes.
This repair would have cost $164 through A&E factory service.
The glass broke after I took the oven door off to tighten the handle which had become lose.....There are 4 screws and one of th 4 had come out , hence the lose handle....So I tightened the 4 screws which were in a metal bracket only to find out under all the foil wrap was glass, and by tightning the screws they fractured the glass into a million little shards of glass...who knew the glass was the full size of the door, and who knew the metal bracket was over top of the glass... too much presurre and the glass explodes. So what should have been an easy re-tighten job cost me alot of time and money.rather than tighten the 4 screws down too hard and break the glass agin, I gentley tightened and used lock tight glue so the screws would not come out again.....Hope that saves someone the problems i had to go through.