GAP39AA Amana Range - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Purchased home but stove had no broiler pan.
-
Raymond from BLOOMINGTON, MN
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
14 of 20 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ignitor did not spark when turning the know
Had to remove the 4 range knobs, and the oven knob and then the facie. Two screws under the end caps and two on each side from the back on each end. Design defect: one of these screws which attaches through the frame to the facie also attaches the support which holds up the range top. Take that one off last. Remove the two wires that attach to the oven light switch. After detaching the power supply to the defective ignition unit, it just pulls right off. Push the new switch on over the knob shaft and reassemble.
Parts Used:
-
Richard from Lansing, MI
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
9 of 11 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
We had totally obliterated the numbers on my old stove knobs
The knobs were a perfect replacement and I just slid them onto the posts on which the old ones were on. Although my range is a Glenwood I think that the parts are now made my Whirlpool (not exactly sure) but they are a perfect match. My order came so quickly and I am thrilled with the transaction. I didn't think I would ever find the replacement knobs and thought I might have to get a new range as you could not read the oven temperatures at all on the old knobs.
Parts Used:
-
Fern from Hull, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
12 of 21 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The Oven Would Not Light
Removed the defective igniter, removing one screw and disconnected wire, replaced new ignighter in reverse fashion. And WELLA! The old oven works again!!
Parts Used:
-
RICHARD from GLOVERSVILLE, NY
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
10 of 17 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Left rear burner would not ignite
Removed the burner plates. Lifted up the range top. Removed the knobs. Unbolted the 2 rounded nuts at top of face plate. Removed the 4 screws that hold the face plate in place from behind. Un plugged the old switch and plugged in the new one and bam! The burner worked. Thanks, Super fast shipping! The part was here in less than 36 hours. John, N.J.
Parts Used:
-
John from Perth Amboy, NJ
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers
5 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
two burner ignitors would not function on cook stove
1. ordered two new switches
2. installed switches
3. all ignitors work
Really appreciated the pictures of the parts--made selection very easy.
2. installed switches
3. all ignitors work
Really appreciated the pictures of the parts--made selection very easy.
Parts Used:
-
Warren from Las Cruces, NM
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
5 of 8 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Right front gas burner ignitor wouldn't spark
I used the experience of another user posted on your web site. I removed all the gas control knobs and then I followed his instructions about removing the four phillps head screws that held the front plate in place. Once I had it loose and flipped the plate out, it was simple to disconnect the old ignitor switch and install the new one. Simply reversing the process put the range back in proper order. Took a little over 15 minutes to accomplish.
Parts Used:
-
Joseph from Lake George, CO
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
5 of 8 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Needed a new knob
-
Karen from Mt Kisco, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
2 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Original knobs with number readings worn off
Took the old knobs off and put the new ones on...voila!!
They fit perfect and even had the same part number stamped inside. Perfect fit and just like new!
Wasn't much of a repair per se but wanted to give a good review. The old knobs were over 30 years old so I was worried I wouldn't be able to find an exact replacement but PartSelect had the exact match.
They fit perfect and even had the same part number stamped inside. Perfect fit and just like new!
Wasn't much of a repair per se but wanted to give a good review. The old knobs were over 30 years old so I was worried I wouldn't be able to find an exact replacement but PartSelect had the exact match.
Parts Used:
-
Julie from ROSAMOND, CA
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Knob writing worn off
I pulled off the old knobs and then placed the new knob. No tools needed!
Parts Used:
-
Susan from CHICAGO, IL
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Needed 2 burner knobs for my 20+ year old range
I have a gas oven range and 2 of the knobs were stripped, making it difficult to control the heat. My appliance is at least 20 years old. I thought I'd have to replace the whole thing. I found your website, did a search, and found exactly what I needed. The knobs fit perfectly. Although not an exact match to the originals, they work, and that's all I care about. Easy and inexpensive fix.
Parts Used:
-
Barbara from Alameda, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
broiler pan missing
-
RAYMOND from JACKSONVILLE, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Needed to replace the 4 chrome bowl liners on our Glenwood Gas stove
It was straight forward to find the part which could be identified by picture and detailed dimensional description. Very easy to throw out the old rotten liners and replace them with the parts sent.
Parts Used:
-
STEVEN from MARSHFIELD, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
3 of 11 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Wrong oven thermostat
-
William from Lancaster, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
The top seal on my Range broke
The repair was really easy! I read a review where the gentleman had order the wrong size and that had me a little worried because I did not specify a size. There were three seals on my range so I figured if one broke I might as well replace all three. When I received the seals they were the right size and it took me less than five minutes to put them on. No tools needed because they had hooks on each end. Thanks a lot!
Parts Used:
-
Clara from Missouri City, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!