This part is a replacement wheel assembly for your lower dishrack. The wheels on the dishrack allow it to roll in and out of the dishwasher efficiently. If one of your wheels is broken or warped, you ...
Ask our experts a question about this model and we'll get back to you as soon as possible!
12 questions answered by our experts.
< Prev
1
2
3
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Simon
January 3, 2020
There is two gaskets I am interested in, one runs inside the frame and secures tightly against the door when closed and the other is at the bottom of the door. I need to order them both and need the parts numbers to do so. Thanks
For model number FPHD2491KF0
Hello Simon, Thank you for contacting us. I have researched the model you have provided and have found the part you are looking for is PartSelect Number PS2379444 for the Gasket around the cabinet. The bottom seal is only sold as part of the Door Liner, PartSelect Number PS2379424. We hope this helps!
Not filling with enough water. Soap dispenser not always opening
For model number FPHD2491KF0
Hello Victor, Thank you for the question. We suggest first checking the water pressure to the appliance. You can also check the valve. The ports where the fill hose connects can become blocked with build up and not allow water to flow through. We hope this helps.
The rollers on the upper rack of my dishwasher have disintegrated so i need to replace them. Searching the part manual i cannot find that there is a possibility of purchasing just the rollers....is this correct? the rack itself is in like-new condition, i just need the rollers.
For model number FPHD2491KF0
Hello and thank you for writing.
On your model,. the wheels are not sold individually they come as part of the rack assembly. So you need to purchase the rack PS2379463. We hope this helps. Please contact us anytime if you require further assistance.
Hello, i need to replace drain hose, and i found two check valves in the hose that i also need but nor sure where they go. Thanks for any help.
For model number FPHD2491KF0
Hello Chuck, thank you for your inquiry. For your model FPHD2491KF0, the correct drain hose is part number PS9492481. As for the valves, please refer to diagram "BOTTOM FRAME DRY SYSTEM". It is figure number 36 I hope this information helps!
Was this helpful?
Thank you for voting!
Divyang
December 16, 2021
Leakage from front bottom right side. Looks like the back gasket is broken, is that be the reason?
For model number FPHD2491KF0
Hello Divyang, Thank you for the question. If the gasket is damaged it can cause it to leak since it is not keeping a seal. The Gasket should be replaced. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
Disconnect from power Unscrewed 4 phillips screws from top of outer door. Unscrewed 2 screws each siide of door. Lower outer door section drops away. Note wiring sequence on dispenser, then disconnect wires. Unscrew 6 screws on dispenser and lift dispenser out.
Place new dispenser in place (note orientation), ann fasten in place with screws, remembering to replace wire retainer on left lower screw. Reconnect wires to dispenser correctly. Slide lower outer door over tabs and secure with the 4 side screws. Ensure lower door is up under control panel and secure with the 4 top screws.
Fill dispenser with detergent, reconnect power and test run while enjoying a cup of tea in celebration of a job well done..
replacing dishrack was simply removing old and sliding new onto track. however, removing and reinstalling water dispenser blade mounted on bottom of existing rack to new rack required much more time and effort .I needed to use flat screwdriver to pry plastic clamps apart and then a pair of channel locks to release assembly from original rack. It took some effort to finally accomplish . I believe all models that use this replacement rack would have this same issue with the dispenser blade and instructions for re-installation should accompany the new rack or better yet, new blade should be included on rack for those not familiar with using tools.