FH4A8FDMK4 (ALSEEUS) LG Dryer - Overview

Diagrams for FH4A8FDMK4

See every part. Know exactly what you need.

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Washing Machine Drain Pump – Part Number: 4681EA2001T
$138.95
In Stock
Washing Machine Drain Pump
★★★★★
★★★★★
(111)
Part #4681EA2001T
The drain pump and motor assembly may also be known as the washer drain pump and is a part for your washer. The drain pump helps expel water from the washing machine. The drain pump is activated after the spin cycle speed is maintained for a specific period of time. To make this installation you will need a Phillips screwdriver, a small flat-blade screwdriver, a pair of needle-nose pliers, and a pair of slip-joint pliers. Note that the pump casing is not included. This medium-difficulty repair may vary, but can generally be started by disconnecting power, then removing the top of the washer by taking out the four back screws and two small brackets. Then, remove the front panel by taking out the two screws and eight tabs that should be taken from the top. Moving down the front of the washer, remove the door, latch, tub gasket, and drain cover. Disconnect the drain hoses and clip from under the drain assembly, and install new assembly from there. Reassemble parts in direct reverse order -- taking photos during disassembly and keeping parts clearly organized can help here. Despite the number of steps, you will only need a standard Phillips screwdriver to complete this repair.
Water Inlet Valve - Hot – Part Number: 5220FR2006H
$67.05
In Stock
Water Inlet Valve - Hot
★★★★★
★★★★★
(18)
Part #5220FR2006H
This hot water inlet valve is designed to regulate water flow into the washing machine during operation. Featuring a standard hose fitting inlet and a single water outlet, it opens as needed to allow hot water into the appliance. If the valve is defective, you may notice slow filling, no filling at all, or water leaks. A simple way to test the valve is to unplug the washer when the issue occurs—if water continues to flow, the valve is likely faulty and should be replaced. The part measures approximately 3 inches in length by 3 inches in width and is sold individually.
Rear Tub Gasket – Part Number: 4036ER2004A
$47.25
In Stock
Washer Tub Bearing, Rear – Part Number: MAP61913707
$60.45
In Stock
Washer Tub Bearing, Rear
Part #MAP61913707
This tub bearing is for washers. Tub bearing supports the spin basket shaft at the tub. Unplug the washer and shut off the water supply before installing this part. Wear work gloves to protect your hands.
Pump Filter – Part Number: 383EER2001A
$34.22
In Stock
Pump Filter
★★★★★
★★★★★
(3)
Part #383EER2001A
This replacement pump filter, also known as a filter assembly, is a genuine OEM part for your washer or washer/dryer combo. Before beginning this repair, turn off the power and water supply to your washer. The filter assembly may need to be replaced because it is broken or is leaking water. To locate the filter assembly, pry open the small door on the front of the washer, using a flat-blade screwdriver. Unplug the drain hose next to the filter and drain the water into a bucket. Then unscrew the pump filter, and replace with your new one.
Washer Switch Assembly – Part Number: EBF61315802
$84.65
In Stock
Washer Switch Assembly
★★★★★
★★★★★
(1)
Part #EBF61315802
This door lock switch is a key component in compatible washing machines, designed to signal the control board when the door is securely closed. Once engaged, it enables the locking mechanism and allows the wash cycle to begin safely. Constructed from black, gray, and white plastic, this switch may need replacement if your washer struggles to start or fails to lock properly. Installation requires partial disassembly of the appliance and basic tools including a screwdriver, drill, and needle-nose pliers. Sold individually.
Washer Hose Connector – Part Number: 5214FR4006G
$15.35
In Stock
Washer Hose Connector
★★★★★
★★★★★
(1)
Part #5214FR4006G
This part is the replacement connector hose or clean-out drain hose for your washer. It is black in color and is sold individually. The connector hose drains water out of the washer if the drain cycle is not working. If the hose breaks, it will not be able to drain the water properly, and you may experience a water leak. Be sure to disconnect your washer from the power source, as well as the water source before you begin this repair. This is an OEM part sourced directly from the manufacturer.
Washer Tub Bearing – Part Number: MAP61913708
$69.25
On Order
Washer Tub Bearing
Part #MAP61913708
Tub bearing. This part is very difficult to install. The manufacturer recommends replacing the complete rear tub and bearing assembly.
Locking Pin – Part Number: 4774FR3118B
$13.15
Special Order
Locking Pin
Part #4774FR3118B
The locking pin is used to hold the shock absorber on the washer. There is a pin used at the bottom and top of the shock absorber. Sold individually.
Bolt Assembly – Part Number: 4040FR4051C
$26.35
In Stock
Bolt Assembly
Part #4040FR4051C
Hook Locker – Part Number: MFG62579002
$41.75
In Stock
Hook Locker
Part #MFG62579002
This genuine OEM washer door hook locker is designed to secure the washing machine door during operation, helping ensure cycles run safely and without interruption. The hook engages the door lock mechanism to keep the door firmly closed throughout washing and spinning. Replacing a worn or broken hook can resolve issues such as the door not locking, the door popping open mid-cycle, or door-related error codes. Installation is typically straightforward, making it a practical solution for restoring proper washer operation.
Drain Hose Cap – Part Number: 5006ER3009A
$13.15
Special Order
Drain Hose Cap
★★★★★
★★★★★
(1)
Part #5006ER3009A
This drain hose plug, also known as a hose cap, is a genuine OEM part for your washing machine. This plug caps the drain hose from the pump housing, and helps prevent leaks from your washer. Before beginning this repair, make sure the power and water sources to your washer are shut off. To access the pump housing, open the pump filter cover, pull out the drain hose, remove the old plug and replace it, first draining the remaining water from the drain hose.

Common Symptoms of the FH4A8FDMK4

How this model fails, and the parts that fix it.

Watch our pros, then fix it yourself.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Washing maching wouldn't drain
592 of 761 people found this instruction helpful.
  • Jorge from Apple Valley, CA
  • Easy
  • 1- 2 hours
  • Screw drivers
Removed the top of the washer by removing the 4 back screws and 2 small brackets. Then I removed the front panel, this was actually the hardest part, 2 screws and 8 tabs that you pop out carefully from the top of the panel. I only disconnected the power button and was able to rest the panel on top of the washer. The rest of the washer cam e apart quickly just moving down the front of the washer and removing the door, latch, tub gasket, drain cover. Removing the pump was just a mater of disconnecting the drain hoses, and one clip under the drain assembly. 3 screws attach the drain to assembly to the pump and only 2 wires that are clearly marked. Reassembly is just going back through in reverse order of disassenbly. The best thing about this is that it all comes apart with a standard phillips screwdriver.
Was this helpful?
Thank you for voting!
noisy operation, sometimes did not drain, gave OE code
60 of 81 people found this instruction helpful.
  • Michael from RALEIGH, NC
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
Thank you for the very helpful YouTube video. After watching the video, I was able to diagnose the problem, buy the part from your website, and complete the repair. This is my personal machine - I am not a professional repairman.
Was this helpful?
Thank you for voting!
Water was filling continues even the machine was unplugged
20 of 24 people found this instruction helpful.
  • Sanjay from HOLTSVILLE, NY
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers, Wrench (Adjustable)
I did repaired while looking at video at your site .thanks to your team ..
Was this helpful?
Thank you for voting!