This aluminum grease filter is a genuine replacement component designed for use in select over-the-range microwave models. Measuring approximately 7-7/8 inches by 5-7/8 inches with a thickness of 1/16 inch, it fits into the microwave’s exhaust system to trap airborne grease particles during cooking. Constructed from high-quality aluminum ...Read moremesh, the filter helps maintain airflow efficiency and improves indoor air quality by preventing grease buildup in the ventilation system. It is recommended to measure your existing filter before ordering, as dimensions may vary slightly between models. Installation is simple and typically involves sliding the filter into the designated slot beneath the microwave.
The relay switch may also be known as the door micro switch and is a part for your microwave. The function of this part is to monitor the door latch and communicate whether the door latch is open or closed to the electronic control board. Before making this repair, you will want to make sure to unplug your microwave and discharge the capa...Read morecitor. Your microwave capacitor is able to store electricity in large quantities even after it has been unplugged. The most common reason for replacing your relay switch is if the microwave will not turn on but your timer still runs..
This vent grille mounts on the top of the microwave above the door. This vent grille is for microwaves.
Vent grille covers components inside the microwave while allowing airflow through the slats.
Unplug the microwave before installing this part. Wear work gloves to protect your hands
Ask our experts a question about this model and we'll get back to you as soon as possible!
We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
2
3
Next
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Robert - For model number FGMV174KFC
February 19, 2020
Door will not close unless you push hard and hold it closed.Door does not lock
Hello Robert, thank you for your question. We would recommend replacing Door Latch Part Number: PS979580, Door Latch Spring Part Number: PS979582, and switch holder PartSelect Number: PS979558 to fix that issue. I hope this helps.
3 peoplefound this instruction helpful.
Was this helpful?
Thank you for voting!
Mark - For model number FGMV174KFC
December 14, 2019
If there is no power to the display or the microwave would that it be fuse? Or relay switch.
Hello Mark and thanks for writing.
It certainly sounds like a faulty Fuse PS466969 test the part and replace it if needed. We hope this helps. Please contact us anytime.
2 peoplefound this instruction helpful.
Was this helpful?
Thank you for voting!
Dennis - For model number FGMV174KFC
December 15, 2019
The push button control panel is loose ,looks like the locking tabs that hold the panel on are not there,what can i do?
Hello Dennis and thanks for writing.
You might have to replace the touch control PS2369351 or the cover it sits in PS2369356, check exactly which parts have been broken off. Most likely it is the cover that has become loose. We hope this helps. Please contact us anytime.
The door has dropped just a bit and the light won’t go off when you shut it. The door isn’t completely latching when you shut it.
Hello Terri, thank you for reaching out. We would recommend checking the door's hinge screws and making sure that they all are tight. If that is not the problem or if you have already fixed that, then you will have to replace the Door Latch, part number PS979580. If you require assistance placing an order, please contact customer service. We hope that helps!
Microwave turns on, turntable spins
Problem is unit makes at least twice as much noise as did previously
Hello Lee, Thank you for your inquiry. For safety reasons, since the microwave capacitor can still store electricity even when the microwave is unplugged, it is usually advised that you discharge the capacitor before any attempt at repair. We have included a link on how to do so. Researching the model number that you have provided, it could be an issue with the turntable motor, the magnetron, the stirrer motor, and the fan motor. You can test the parts with a multimeter. If you are unfamiliar with how a multimeter functions, we have videos available to assist you. We hope this helps and if you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Timer would run but the microwave won't start
92 of 150 peoplefound this instruction helpful.
Tim from Chicago, IL
Easy
30 - 60 mins
Screw drivers
I first removed the top plate above the microwave door (3 screws), then I removed the plate containing the buttons and clock. The microwave has 3 relay switches and they are in a little holder. The holder was too difficult to remove so I just removed the bottom switch and replaced. The microwave started right up.
Was this helpful?
Thank you for voting!
Turntable stoped working
29 of 34 peoplefound this instruction helpful.
steve from New Bern, NC
Really Easy
15 - 30 mins
Screw drivers
Removed the 3 screws to drop the lower panel and, removeed the turn table plate and ring. Then removed the 2 screws holding the motor, the 2 wires attached to the motor and removed the old motor.Replaced the new motor in the reverse order. DO NOT FORGET TO UNPLUG THE MICROWAVE FIRST.
Was this helpful?
Thank you for voting!
microwave wouldn't turn on but timer worked.
35 of 64 peoplefound this instruction helpful.
Steve from Moorhead, MN
Easy
Less than 15 mins
Pliers, Screw drivers
was told buy a repair person to check the door micro switches as it was a common problem. removed the top plastic air grill to get access to the screw that holds in place the control cover. After unplugging the unit, i took out the (2) screws that held in the switches and removed them (3). One switch was a bit melted so i tested it with a
... Read more 12 volt battery and it was bad. Ordered a new one from Part select and got it fast . Works great .
My Orders
