The relay switch may also be known as the door micro switch and is a part for your microwave. The function of this part is to monitor the door latch and communicate whether the door latch is open or c...
This vent grille mounts on the top of the microwave above the door. This vent grille is for microwaves.
Vent grille covers components inside the microwave while allowing airflow through the slats....
Mounting hardware sold separately. This part has been redesigned by the manufacturer and may appear different then the original.
$101.18
Special Order
Questions And Answers for FGMV174KFB
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
9 questions answered by our experts.
< Prev
1
2
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Susan
December 9, 2019
Where do you replace the charcoal filter go
For model number FGMV174KFB
Hello Susan,
Thank you for your question. The charcoal or air filter is behind the vent grille for your model under part PS979601. Hope this helps!
Hi Jermaine,
Thank you for your question. The part number listed under your model number for the complete door is PS2369380. We hope this helps. Thank you and have a great day!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Larry
January 26, 2020
Where is access to interior light bulb?
For model number FGMV174KFB
Hello and thank you for writing.
Take off the vent across the top (three long screws) to expose a single screw over the keypad. Remove the single screw, and the whole keypad console will lift up and off, likely hanging by a plastic tab/support on the bottom. Now you can twist the light bulb plug to remove it from the support structure, change the bulb PS979525. We hope this helps. Please contact us anytime if you require further assistance.
Our above the stove microwave made a loud sparking noise. We opened the door, everything looked fine and we continued to heat the food. After 3-4 more uses, the microwave no longer heats. Everything works except for not heating.
For model number FGMV174KFB
Hello Suzanne, thank you for your question. There are a few parts that could cause that issue. The most common part is the relay switch. We would recommend testing that part first, and if that is fine, the diode should be tested next. The other part that could be the problem is the magnetron. Here are the part numbers. Relay Switch Part Number: 5304440026, High Voltage Diode Part Number: 5304467670, Magnetron Part Number: 5304463439. I hope this helps.
Was this helpful?
Thank you for voting!
Suzanne
February 20, 2020
Does microwave model fgmv174kfb have a ‘wave guide cover’? If so, where is it located and how can i order one?
For model number FGMV174KFB
Hello Suzanne, thank you for your question. There is no wave guide cover but there is a cover for the ceiling of the unit that covers the stirrer motor. That is PartSelect Number: PS2343146. The pin that holds it into place is Part #: PS2343080. I hope this helps.
I first removed the top plate above the microwave door (3 screws), then I removed the plate containing the buttons and clock. The microwave has 3 relay switches and they are in a little holder. The holder was too difficult to remove so I just removed the bottom switch and replaced. The microwave started right up.
Removed the 3 screws to drop the lower panel and, removeed the turn table plate and ring. Then removed the 2 screws holding the motor, the 2 wires attached to the motor and removed the old motor.Replaced the new motor in the reverse order. DO NOT FORGET TO UNPLUG THE MICROWAVE FIRST.
was told buy a repair person to check the door micro switches as it was a common problem. removed the top plastic air grill to get access to the screw that holds in place the control cover. After unplugging the unit, i took out the (2) screws that held in the switches and removed them (3). One switch was a bit melted so i tested it with a 12 volt battery and it was bad. Ordered a new one from Part select and got it fast . Works great .
