This grey OEM dishwasher tub gasket is a 73" grey rubber part that creates a seal around the dishwasher to prevent any water leakage during a cycle. If it's damaged or broken, you'll start seeing wate...
$47.19
In Stock
Order within the next 4 hrs and your part ships today!
The single rack roller kit comes with one axle/clip and one wheel/roller. The rack wheel is designed to allow the rack of your dishwasher to roll in and out. If the rack will not complete this task, o...
$8.76
In Stock
Order within the next 4 hrs and your part ships today!
The spray arm rotates and sprays water to clean the dishes inside the dishwasher tub.
This part works with the following brands: Frigidaire, White Westinghouse, Kelvinator, Gibson, Kenmore, Sears, ...
$81.89
In Stock
Order within the next 4 hrs and your part ships today!
This door seal is for dishwashers.
Door seal seals the gap between the opening to the dishwasher tub and the outer edge of the door.
After installing the door seal, shut the dishwasher door and ...
$41.19
In Stock
Order within the next 4 hrs and your part ships today!
This plastic cover and stem assembly helps hold the lower spray arm in place.
$39.53
In Stock
Order within the next 4 hrs and your part ships today!
Questions And Answers for FGID2466QF8A
Ask our experts a question about this model and we'll get back to you as soon as possible!
2 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Karl
February 28, 2022
My dishwasher doesn't drain. Is my drain pump broken?
For model number FGID2466QF8A
Hello Karl, Thank you for your inquiry. We would recommend checking the drain hoses, the flapper valve and the drain filter first for any clogs or damage, and make sure the filter is clean. You can test the drain pump with a multimeter to see if it is faulty. If you are unfamiliar with how a multimeter functions, we have videos available to assist you. We hope this helps and if you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
Dishwasher won’t drain properly on Normal or PowerPlus cycles, but does on Quick Rinse mode. Tested drain pump (it has continuity), checked for clogs in drain line, checked flapper valve, replaced float switch. Any other suggestions?
For model number FGID2466QF8A
Hello Chris, thank you for contacting us. Please check the electronic control board, part number PS12712360, with a multimeter. It manages the functions of the dishwasher such as washing, draining, and drying. It is the probable culprit of the issue. Please reach out to customer service if you need help placing an order. Glad to be of help!
I removed old tub gasket, which the door presses against to make a seal, and put the new one in. Flat tip screwdriver was used to gently press gasket in.
I looked under and found that 2 brass nuts that secured the heater element through the base housing of the dishwasher has split down each side of the nut and no longer was tight enough to keep water from leaking around either end of the heater element. I powered down the dishwasher at the circuit breaker and then reached under the dishwasher and pulled away the 2 wires that were attached to each side of the heater element. I removed the two nuts and replaced them with the parts I ordered from partselect.com. I then put the appropriate wires back at the end of the heater element and ran the dishwasher to check for leaks. No leaks... it was fixed.