This grey OEM dishwasher tub gasket is a 73" grey rubber part that creates a seal around the dishwasher to prevent any water leakage during a cycle. If it's damaged or broken, you'll start seeing wate...
The upper spray arm helps distribute water from the top of the dishwasher tub.This spray arm is a genuine OEM replacement part for your dishwasher. This spray arm is for the upper part of your dishwas...
The silverware basket, used for dishwashers, is in the bottom dishrack. The lower dishrack basket is used to hold eating utensils such as spoons, forks, and knives, and other small tools. If the baske...
The single rack roller kit comes with one axle/clip and one wheel/roller. The rack wheel is designed to allow the rack of your dishwasher to roll in and out. If the rack will not complete this task, o...
The spray arm rotates and sprays water to clean the dishes inside the dishwasher tub.
This part works with the following brands: Frigidaire, White Westinghouse, Kelvinator, Gibson, Kenmore, Sears, ...
This door seal is for dishwashers.
Door seal seals the gap between the opening to the dishwasher tub and the outer edge of the door.
After installing the door seal, shut the dishwasher door and ...
This door latch with the switches is a simple on/off mechanism that prohibits the dishwasher from operating when the door is open.
$56.41
In Stock
Questions And Answers for FGID2466QF5A
Ask our experts a question about this model and we'll get back to you as soon as possible!
15 questions answered by our experts.
< Prev
1
2
3
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Marti
March 26, 2020
All the lights on the control panel have gone out. There’s no error code or anything. What could the issue be?
For model number FGID2466QF5A
Hello Marti, Thank you for the question. If the appliance is receiving power, this can be caused by a defective Electronic Control Board, PartSelect Number PS12365809. We hope this helps.
I am wondering if you have a twist cap for the rinse aid dispenser?
For model number FGID2466QF5A
Hello Chere, thank you for your question. The rinse aid cap is PartSelect Number PS421128. This part is white not grey but will fit. I hope this helps.
Looking to solve problem ... water is not spraying. it fills and drains just fine. stopped working a couple days ago.
i replaced the circulation pump with a used one. still not working. with replacement pump, i hear a thumping sound and a small amount of spray shoots out the hole for the top rack (more than it was with the original pump). nothing is coming out of the spray arms on the bottom. ideas? thanks!
For model number FGID2466QF5A
Hello Sean, thank you for your question. We would recommend checking the water feed tube and the spray arms themselves. If the spray arms are clogged they are unable to spin. If those are clear the issue could be with the turbidity sensor PartSelect Number: PS2363559 or pump and motor. I hope this helps.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Sean
March 18, 2020
When the circulation pump is running correctly, does it push water through the spray arm mount in spurts, or with a constant flow?
For model number FGID2466QF5A
Hello, Thank you for your question. The circulation pump usually allows water through the spray arms at a constant stream. We hope this helps.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Sean
March 9, 2020
What does a turbidity sensor do? Thanks!
For model number FGID2466QF5A
Hi Sean, thank you for your question. The turbidity sensor on your appliance is able to register the amount of debris floating inside of your water and helps signal the board on how long a wash cycle needs to be. Good luck with your repair.
Was this helpful?
Thank you for voting!
< Prev
1
2
3
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
Repair was simple. I unscrewed the old grommet which held the old spray arm and screwed-on the new one. About 30 seconds was required. Other people having this problem should note that the spray-arm is made of three pieces which are inseparable when the arm is new. The arm is sold in this form. However, when your machine is having the problem that the arm falls off, the three pieces become separate. When you want to replace the spray arm, only one new part needs to be ordered because this part encompases all three components.
I removed old tub gasket, which the door presses against to make a seal, and put the new one in. Flat tip screwdriver was used to gently press gasket in.