This grey OEM dishwasher tub gasket is a 73" grey rubber part that creates a seal around the dishwasher to prevent any water leakage during a cycle. If it's damaged or broken, you'll start seeing wate...
This dishwasher water inlet valve is a genuine OEM component designed to regulate water flow into the appliance during the fill cycle. Typically located behind the lower kickplate panel in either fron...
The upper spray arm helps distribute water from the top of the dishwasher tub.This spray arm is a genuine OEM replacement part for your dishwasher. This spray arm is for the upper part of your dishwas...
The single rack roller kit comes with one axle/clip and one wheel/roller. The rack wheel is designed to allow the rack of your dishwasher to roll in and out. If the rack will not complete this task, o...
The spray arm rotates and sprays water to clean the dishes inside the dishwasher tub.
This part works with the following brands: Frigidaire, White Westinghouse, Kelvinator, Gibson, Kenmore, Sears, ...
This part is a replacement spray arm support for your dishwasher. It is made of white plastic and is approximately 3 inches long, 1 inch wide, and 3 inches tall. This is the support for the lower spra...
If your dishwasher won’t start or the door won’t close properly, the latch assembly might need replacing. This part helps keep the door securely shut and includes a switch that stops the dishwasher fr...
The drain hose connects to the pump located below the lower spray arm. It aids in proper dishwasher drainage. Size: 7.5 feet long
$49.42
In Stock
Questions And Answers for FGHD2465NF1A
Ask our experts a question about this model and we'll get back to you as soon as possible!
14 questions answered by our experts.
< Prev
1
2
3
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Frank
November 14, 2022
It’s blinking ER. It did this last week and then started running again. It starts and you hear the pump running, stops again. I turned breaker off to see if that cleared the message but it didn’t work. Any help would be greatly appreciated
For model number FGHD2465NF1A
Hello Frank, thank you for contacting us. The error code ER indicates that something is wrong with the keypad. A button might be failing due to steam getting inside. We would recommend accessing the keypad area and checking if all the buttons appear fine. If not we would recommend cleaning the board. If this does not help, there is probably some issue with the control panel, part number PS8760856. We would also recommend running a continuity test on the electronic control board, part number PS12365809. Customer service is always available to help you place an order if you are having trouble doing so. Good luck with your repair.
I get an error code "uo" and the machine stops 2 minutes after I start it.
For model number FGHD2465NF1A
Hello Jess, thank you for your question! This error means that your drying vent is stuck open. While in the wash cycle, the main control board does not receive a signal from the vent assembly that the vent plunger is closed. Plunger status is sensed with the optical sensors in the vent assembly. Your vent assembly and blower, part number PS12741853, are part of the door itself. We hope this information is useful!
Trips on false power failure reguardless of wash cycle. Trips on every 5th or 6th wash.
For model number FGHD2465NF1A
Hi Michael, thank you for reaching out. We would suggest checking the wire harnesses of the main control board. If they are fine, the issue could be with the main control board, part number PS12365809. It manages the functions of the dishwasher, such as washing, draining and drying. You may need to replace it to fix the issue. We hope this sorts out your problem!
Can you give me the dimensions of this model? Width, height and depth?
Thank you!
For model number FGHD2465NF1A
Hi Amy, thank you for the question. Based on our research, your model has approximately the following dimensions:
Width: 24 inches.
Depth: 25 inches.
Height: 33 1/2 inches.
We hope this information helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Guy
April 29, 2023
can I buy just the Despenser final Rinse cap
For model number FGHD2465NF1A
Hello Guy, Thank you for your inquiry. According to the manufacturer, the white cap, part# PS421128, will fit this dispenser. The grey cap is only available as part of the dispenser. We hope this helps
Repair was simple. I unscrewed the old grommet which held the old spray arm and screwed-on the new one. About 30 seconds was required. Other people having this problem should note that the spray-arm is made of three pieces which are inseparable when the arm is new. The arm is sold in this form. However, when your machine is having the problem that the arm falls off, the three pieces become separate. When you want to replace the spray arm, only one new part needs to be ordered because this part encompases all three components.
Remove the bottom cover plate. Disconnect the water inlet and black rubber hose. Remove 2 mounting screws. Pull out electrical connector. Reverse order. Be sure to get the brass inlet connector really tight so it won't leak. I did the final tightning after the part is mounted. Not a bad repair at all. The only problem was that it leaked in the first place and messed up my subfloor and laminate flooring.
