FFT40849-0C Frigidaire Freezer - Instructions

It was very easy to remove the broken parts of the freezer door handle still secured by screws and then attach the new handle. However, I was shocked to find that the door handle screw cover plate was not included as part of the door handle replacement issued, which I felt was misleading. Fortunately that portion from my old broken handle was still intact, though is yellowed with age, so was able to snap that in place on the new partial-handle replacement which you sent. It seems to me that to omit this portion as part of the complete handle replacement didn't make much sense, as it rendered the new replacement handle incomplete.

Bought a new
capacitor.

This was a simple job. Raised the flap in the back that houses the compressor, removed the wire that holds the relay, pulled out the old relay and pushed the new one on. Replaced wire holder and that was it. Plugged it frig and freezer is at zero and lower compartment at 35. As easy as brushing your teeth!

I located the part that was the culprit as it had buzzed very much before quitting. This is an easy removal as the part is in a two prong jack and just needs to be carefully removed with the new part inserted back in the jack provided. The refrigerator works fine now, but the run capacitor will still buzz on start up of the compressor. I do hope this is normal in this model? anyway it runs fine mow. Thank you.

The site offers a video for this part which worked perfectly. In addition to replacing the part, since the cardboard panel was off, we also cleaned all the dust off of the coils which someone recommended to do annually.

The repair was really easy - I used a phillips head screw driver to remove the screws and broken pieces of the handle, screwed the new one on and snapped the handle insert into place. I was thrilled to be able to find the parts so easily (the information you have online is really helpful!), the parts arrived much faster than I anticipated and the handle was easily replaced! Thank you!

Old handle was off already. Took the to screws from old handle, put the new one on screwed it on and that did it.

I ordered the handle , which was easy and resonable priced.
I used a cordless screw driver . And it was done in under 30 seconds . Quick repair

By simply popping off the handle cover the two screws were revealed which attach the handle to the door. New handle fit exactly like the old one. Easy peezzy lemon squeezy.

A little research told me the hum plus no cooling was either the compressor or the relay. I ordered the new relay and put it in but it didn't fix the problem. I ended up having to buy a new fridge, but it was worth the $30 gamble to see if I could fix it on the cheap and it saved me the money a service call would've cost. Pretty easy installation, just in a tight space on my model.

Could not be easier and I think it took me longer to open the packaging than it did to install. Remove the insert from the face of the old handle and remove the two screws (top & bottom) beneath the insert & discard broken handle (retain original screws). Put original screws through new handle, place in position and drive the screws in. Then snap in the insert panel. (My insert was old & brittle and did crack upon removal, but I had anticipated that and ordered a new insert as well.) Took 5 minutes....but I'm pretty handy and it might take someone else 6 minutes.

Ordered the Capacitor and the Thermostat Control. Parts were received in a matter of a few days, easy to install, but did not fix the problem. Had to call a repairman to fix the problem (compressor relay - this part not available to order for this model number with Parts Select). Will continue to use Parts Select in the future for other parts, but not happy that the actual part I needed was not available - had to use other methods.

Ordered the replacement handle and insert. I replaced the handle in about 10 minutes.

Remove the cardboard access cover at the bottom back of the fridge. On the left side, locate the run capacitor. Remove it by prying it loose from its socket, after first removing the wire hold down clamp. One wonders why the clamp is there, which makes it difficult to get the run capacitor out. Be careful not to disrupt in any way the copper refrigerant tubes. If you mess them up, you will have wasted your time and effort trying to repair the machine. I was lucky, since a failed run capacitor is the problem only about 12% of the time, based on what I’ve read. Hallelujah! It was the problem with my fridge.

Removed pcs. of old handle, replaced new handle, installed handle trim strip. Took less than 5 min. Thanks