This crisper cover front support is used to keep the crisper shelf in place and may need replacing if the door will not open or close. This white, OEM part measures roughly 1 inch in diameter and can ...
This authentic rear crisper support is a white, plastic part which is rated as "easy" to install by our customers. This OEM part replaces the rear crisper cover support in your fridge and mounts to th...
This door bin is for refrigerators.
Door bin attaches to the inside of the refrigerator door and typically holds jars and bottles.
Follow the instructions in the owner's manual for installing t...
This NSF-Certified OEM filter is white in color with a plastic housing and extruded carbon filter media. It measures 2.3-Inches deep, 9.1-Inches high and 2.3-Inches wide. It fits certain Frigidaire si...
This door bin holds items on the door of your refrigerator. They are sometimes called Cantilever Shelves as they are supported by the back of the shelf itself to the door of your refrigerator. Sold individually.
This part helps the compressor kick on and off while maintaining a constant temperature to keep things frozen in your freezer. The run capacitor is attached to the compressor. This part is 120 volts a...
This crisper drawer frame does not include the glass. The crisper drawer frame a frame that supports the crisper drawer and also holds the shelf that serves as the lid for the crisper drawer. It has r...
This is the replacement water filter base for your refrigerator. It is approximately 3-1/2 inches by 3 inches. It is made of white plastic with two blue water filter receptacles. The water filter base...
$75.85
In Stock
Questions And Answers for FFSS2315TS2
Ask our experts a question about this model and we'll get back to you as soon as possible!
3 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Karen
August 15, 2023
how to change the water filter
For model number FFSS2315TS2
Hello Karen, thank you for reaching out. According to our research, the water filter is located at the top right side of the refrigerator compartment. In order to replace it, follow the following steps: First, turn off the ice maker. Remove the filter by pushing on the end/face of the filter. Slide the old water filter cartridge straight out of the housing and discard it. Using the alignment guide, slide it gently into the filter housing until it stops against the snap-in connector at the back of the housing. Push firmly until the cartridge snaps into place. You should hear a click as the cartridge engages the snap-in connector. Press a drinking glass against the water dispenser while checking for any leaks at the filter housing. Any spurts and sputters that occur as the system purges air out of the dispenser system are normal. After filling one glass of water, continue flushing the system for about four minutes. Turn on the ice maker. Press and hold the water filter button on the ice & water dispenser control panel for three seconds. When the display changes from red to green, the status has been reset. We hope this helps!
Was this helpful?
Thank you for voting!
Neal
September 12, 2022
I need to replace the water filter cartridge. What part number is that. Thanks Neal
For model number FFSS2315TS2
Hello Neal, thank you for contacting us. We have researched the model you have provided and have found the part you are looking for is part number PS3412266. If you would like assistance placing an order, please contact customer service. Good luck with your repair!
How to put water and ice filter in refrigerator . I bought this filter WF3CB and it keeps popping out of place in the refrigerator.
For model number FFSS2315TS2
Hello Karen, thank you for the great question. The most likely reason the water filter won't stay in place is it is not properly aligned in the base. If the cap at the top of the filter is damaged or it is covered with protective materials, it may not stay in place. It's also possible that the water filter base is damaged or defective. Using the alignment guide, slide it gently into the filter housing until it stops against the snap-in connector at the back of the housing. Push firmly until the cartridge snaps into place (you should hear a click as the cartridge engages the snap-in connector). If this does not help you will need to inspect the water filter housing, part number PS8689210. The metal clip that holds the filter gets stretched over time and won't grab the filter correctly anymore. We hope this sorts out your problem!
In my specific appliance the water valve is located in the bottom right hand corner looking at it from the back. To get to it I remove the thin layer of cardboard the covers the back of the fridge. I then proceeded to disconnect the 1/4" copper tubing which is the water feed coming out of the wall. Then I removed the screws that hold the valve assembly in place. I took the water valve out and removed the electrical connections as well as the plastic tubing which feed the water dispenser and the ice maker. To install the new water valve it was just a matter of reversing steps.
Used pliers to remove the residual broken stud that was still attached to the wall of the refrigerator, and then just pushed the new part in place. The longest time was spent in removing the food and crisper drawers.
Even though my wife said that our icemaker broke, there was actually nothing wrong with it. It was the valve that let water flow in during the 'harvest' cycle. A real easy way to test the icemaker without voltage and current measurements, is to fill the tray by hand with a little cup of water; wait till the water freezes and see if the maker dumped the ice into the bin.