The Lower Spray Arm is used in your dishwasher to spray water and clean your dishes. If broken there will be visible damage or your dishes may no longer be cleaned properly. If your spray arm is broke...
This grey OEM dishwasher tub gasket is a 73" grey rubber part that creates a seal around the dishwasher to prevent any water leakage during a cycle. If it's damaged or broken, you'll start seeing wate...
The single rack roller kit comes with one axle/clip and one wheel/roller. The rack wheel is designed to allow the rack of your dishwasher to roll in and out. If the rack will not complete this task, o...
This door seal is for dishwashers.
Door seal seals the gap between the opening to the dishwasher tub and the outer edge of the door.
After installing the door seal, shut the dishwasher door and ...
Ask our experts a question about this model and we'll get back to you as soon as possible!
4 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Jeff
March 19, 2023
FILLS, ALSO DRAINS. WONT CYCLE AND WASH?? BUT GOES THROUGH COMPLETE CYCLE. BOARD??
For model number FFCD2413UW2A
Hi Jeff,
Thank you for your question. If your dishwasher will not cycle or wash, there are some parts that you will need to check to see which one is causing the issue. We recommend checking the door latch and switches, the electronic control boards, and the motor. We have included a link from our website that you may reference on how to check these parts. Once you have determined the part you need, please call customer service. We look forward to hearing from you!
Dishwasher doesn’t clean dishes nor glassware
On top rack. Soap dispenser doesn’t dispense all
The soap. Does not work well with recommended
cascade pods.
For model number FFCD2413UW2A
Hi Regina, thank you for asking. The issue is most probably with the detergent dispenser, part number PS11770487, but before replacing it, we would recommend checking if the water pump is working fine and the water is being properly circulated. We have attached a relevant video for you to help with the process. We hope this helps, good luck with this repair!
why does the dishwasher load water but does not start?
For model number FFCD2413UW2A
Hi Federica, thank you for reaching out. If your dishwasher fills with water but does not start, there might be blockages inside the dishwasher. Broken glassware or something may block the motor. Check the filter, sump hose, impeller, and drain hose for blockages. If the motor is working fine, you need to check the spray arms. Without regular cleaning, the sprayers may become blocked, and this will affect the cleaning performance of your machine. Please contact us anytime if you require further assistance.
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
I have had to keep replacing the spray arm on the bottom of my dishwasher which takes like 2 seconds to do.. First you open the dishwasher and than pull the bottom basked forward and reach down and pull the spray arm up and pop the bottom of the spray arm off and put it on the new spray arm and slip it back into the dishwasher over the thing that makes it spin around.. but the tricky part is and I didn't know this and this is why my dishwasher spray arm kept falling over and melting on the heating element.. you have to turn it till it clicks in.. and your done..
I removed old tub gasket, which the door presses against to make a seal, and put the new one in. Flat tip screwdriver was used to gently press gasket in.
