The Lower Spray Arm is used in your dishwasher to spray water and clean your dishes. If broken there will be visible damage or your dishes may no longer be cleaned properly. If your spray arm is broke...
$45.60
In Stock
Order within the next 11 hrs and your part ships today!
This grey OEM dishwasher tub gasket is a 73" grey rubber part that creates a seal around the dishwasher to prevent any water leakage during a cycle. If it's damaged or broken, you'll start seeing wate...
$47.19
In Stock
Order within the next 11 hrs and your part ships today!
The single rack roller kit comes with one axle/clip and one wheel/roller. The rack wheel is designed to allow the rack of your dishwasher to roll in and out. If the rack will not complete this task, o...
$8.76
In Stock
Order within the next 11 hrs and your part ships today!
This door seal is for dishwashers.
Door seal seals the gap between the opening to the dishwasher tub and the outer edge of the door.
After installing the door seal, shut the dishwasher door and ...
$41.19
In Stock
Order within the next 11 hrs and your part ships today!
Order within the next 11 hrs and your part ships today!
Questions And Answers for FFCD2413UW1A
Ask our experts a question about this model and we'll get back to you as soon as possible!
5 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Tammy
January 30, 2023
The arm keeping coming off during a wash. What would you recommend I have replaced arm already.
For model number FFCD2413UW1A
Hello Tammy, Thank you for the question. If referring to the Lower Arm we suggest checking or replacing the Lower Spray Arm Support that attaches to the Lower Spray Arm. We hope this is helpful!
Hi Shirley,
Thank you for your question. There is a filter that removes food particles and debris from the water to prevent the drain from clogging. It is located under the lower spray arm. The part number for the filter is PS11770489. We hope this helps!
Hello Shirley, thank you for reaching out. Use the following instructions to remove and clean the glass trap:
1. Grasp the glass trap handle and rotate it 90 degrees clockwise while pressing down on the center of the wash arm.
2. Grab the spray arm in the center and lift the spray arm and glass trap assembly up and out of the dishwasher.
3. Tip the assembly over an appropriate container and tap it to empty the glass trap.
4. Place the assembly back into position, press down on the arm at the center, and rotate the glass trap handle 90 degrees counterclockwise, making sure the glass trap ends in the orientation.
We hope this information helps!
Was this helpful?
Thank you for voting!
Norman
October 12, 2023
Need bottom dish rack
For model number FFCD2413UW1A
Hello Norman, thank you for reaching out. The lower dish rack you are looking for is part number PS12584831. Glad to be of help!
my dishwasher is not draining , the glass trap is clear ,drain hose is not kinked and the disposer is clear
For model number FFCD2413UW1A
Hi Frank, thank you for the question. Based on the description, you have provided the issue could be with the drain pump, part number PS8689824. It removes the water from the dishwasher tub during the drain phase of the dishwashing cycle. You may need to replace it to fix the issue. We hope that helps!
I have had to keep replacing the spray arm on the bottom of my dishwasher which takes like 2 seconds to do.. First you open the dishwasher and than pull the bottom basked forward and reach down and pull the spray arm up and pop the bottom of the spray arm off and put it on the new spray arm and slip it back into the dishwasher over the thing that makes it spin around.. but the tricky part is and I didn't know this and this is why my dishwasher spray arm kept falling over and melting on the heating element.. you have to turn it till it clicks in.. and your done..
I removed old tub gasket, which the door presses against to make a seal, and put the new one in. Flat tip screwdriver was used to gently press gasket in.