The Lower Spray Arm is used in your dishwasher to spray water and clean your dishes. If broken there will be visible damage or your dishes may no longer be cleaned properly. If your spray arm is broke...
This grey OEM dishwasher tub gasket is a 73" grey rubber part that creates a seal around the dishwasher to prevent any water leakage during a cycle. If it's damaged or broken, you'll start seeing wate...
The upper spray arm helps distribute water from the top of the dishwasher tub.This spray arm is a genuine OEM replacement part for your dishwasher. This spray arm is for the upper part of your dishwas...
The single rack roller kit comes with one axle/clip and one wheel/roller. The rack wheel is designed to allow the rack of your dishwasher to roll in and out. If the rack will not complete this task, o...
The drain hose connects to the pump located below the lower spray arm. It aids in proper dishwasher drainage. Size: 7.5 feet long
$35.68
In Stock
Questions And Answers for FFBD2412SS0A
Ask our experts a question about this model and we'll get back to you as soon as possible!
8 questions answered by our experts.
< Prev
1
2
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Darrel
September 13, 2021
How do I find and clean the filter on this model?
For model number FFBD2412SS0A
Hello, Thank you for contacting us. We have researched the model you have provided and have found the part you are looking for is PartSelect Number PS11770489. We suggest watching the How to Video on replacing the Filter and it will show how to remove the filter. We hope this helps!
https://www.youtube.com/watch?v=rrwZ2PnkQkk
We noticed after starting a wash cycle that the "clean" led light wasnt on at the end. Open the dishwasher it seemed to be in dry mode since there was heat, dishes looked clean but there was abnormal amount of water left that wasnt drained. Naturally i checked for clogs none found. Replaced the drain motor. Wondering what else could be causing this.
For model number FFBD2412SS0A
Hello Nick, thank you for your question. We would recommend testing the following parts first. Heating Element Part Number: 154825001, High Limit Thermostat PartSelect Number: PS2331123, Float Switch PartSelect Number: PS3492842. If those parts are fine, the issue could be with the main control board. I hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Lee
April 27, 2023
Every few cycles, my dishwasher stops during the initial rinse cycle. The cycle stops, water is left in the tub, and the detergent dispenser does not open. If I press the Cancel button for 3 seconds, the water drains just fine (good flow into the sink disposer, no blockages in drain or filters). I can then run a cycle normally. A few days later, this same thing happens.
For model number FFBD2412SS0A
Hi Lee, thank you for reaching out. Based on our research, you may need to check the control board, part number PS16620604, and replace it if necessary. We hope this solves your problem!
I start a wash cycle and I can hear it run for 15-20 minutes. I check back later some time and no LEDs are on, the soap has not dispensed things are wet and my roommate reported not all the water had drained. Where should I start?
For model number FFBD2412SS0A
Hello Scott, thank you for asking. If the dishwasher is not draining and does not complete the wash cycle, the issue is most probably with the electronic control board, part number PS16620604. You may need to check the control board to fix the issue. We hope this helps!
The detergent door doesn't open during the entire wash cycle.
For model number FFBD2412SS0A
Hi Gary, thank you for reaching out. Make sure the dispenser is not obstructed. Tall items like cookie sheets and cutting boards placed in the lower rack can block the dispenser, preventing the detergent from dispensing. Verify that the dispenser is not simply clogged with caked-on detergent and give it a good cleaning if necessary. If this does not help, then it could be a faulty detergent dispenser PS11770487. You should check for signs of damage, and replace if necessary. We hope this helps.
Repair was simple. I unscrewed the old grommet which held the old spray arm and screwed-on the new one. About 30 seconds was required. Other people having this problem should note that the spray-arm is made of three pieces which are inseparable when the arm is new. The arm is sold in this form. However, when your machine is having the problem that the arm falls off, the three pieces become separate. When you want to replace the spray arm, only one new part needs to be ordered because this part encompases all three components.
I have had to keep replacing the spray arm on the bottom of my dishwasher which takes like 2 seconds to do.. First you open the dishwasher and than pull the bottom basked forward and reach down and pull the spray arm up and pop the bottom of the spray arm off and put it on the new spray arm and slip it back into the dishwasher over the thing that makes it spin around.. but the tricky part is and I didn't know this and this is why my dishwasher spray arm kept falling over and melting on the heating element.. you have to turn it till it clicks in.. and your done..