This kit includes one bearing, one ball shaft, one ball bearing, one ball bearing retainer, a small tube of high temperature lubricant, and installation screws.
$71.08
In Stock
Order within the next 31 mins and your part ships today!
This thermal fuse limiter, with a limit of 220 degrees Fahrenheit, is manufactured for both gas and electric clothes dryers. Once the internal temperature of the dryer reaches 220 degrees, the heating element cuts out.
$34.73
In Stock
Order within the next 31 mins and your part ships today!
This high limit thermostat has a limit of 260 degrees Fahrenheit. Meaning that it will cut out when the internal dryer temperature reaches 260. This thermostat cuts back in when the temperature drops ...
$119.16
In Stock
Order within the next 31 mins and your part ships today!
***Please Note: This part is a substituted part by the manufacturer. It may appear different, but should still work with your appliance.
$161.95
In Stock
Order within the next 31 mins and your part ships today!
Questions And Answers for FEQ1442ES1
Ask our experts a question about this model and we'll get back to you as soon as possible!
2 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
John
September 21, 2022
Dryer works, but makes a heck of a noise. Sounds like it could be a bearing at the rear. Have replaced the motor, heating element, rear drum bearing kit and blower husing with blower wheel.
For model number FEQ1442ES1
Hello John, thank you for contacting us. We would recommend checking the following parts to fix your issue: Drum Support Bearing, part number PS418807, Drum Belt, part number PS1148434, Drum Glide, part number PS5574052, and Rear Drum Bearing Kit, part number PS459829. We hope this solves your problem!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Lamonica
November 8, 2021
Why my dryer won't start?
For model number FEQ1442ES1
Hello Lamonica, Thank you for the question. If the appliance has power and powers on as normal but will not start the cycle, we recommended replacing the Door Switch. Here are some steps to replace the switch. The top panel is held in place in the front by 3 plastic tabs on the console, and 2 screws In the rear. Remove the 2 screws, slide the top back about 1/2 inch and lift the top off. Open the door, Disconnect the wires from the door switch. Squeeze the release tabs on the ends of the switch and push it out the front. Reverse the procedure to install the switch, then test the dryer for proper operation and heat. We hope this helps!
1. Unplug dryer from outlet 2. Using Lg. flat screwdriver, pry under the front edge of the top and release two spring tabs 3. Lift up top and tilt back out of your way 4. Unscrew two phillips scews on inside of front panel 5. Lift up and out the front panel. Two spring clips at bottom. 6. Rlease tension on drum belt at the motor. Access panel at rear of dryer. 7.Unscrew 3 screws from inside, center rear of drum. 8. Remove drum through the front of the dryer. You may have to spread the sides apart a little bit for it to fit 9. Lift up on the rear drum bearing to remove it from the bearing retainer. ( U shaped plastic socket) 10. unsrew 2 screws and remove the bearing retainer, ground ball. Ball retainer is on outside of dryer. 11. Vacuum everything--duct, blower, lint trap, ect. 12. Intall new bearing retainer and grounding ball, an assistant is helpful at this time, one to hold ball retainer on rear of dryer, one to screw it in from the inside 13. reassemble remainder of parts in reverse order.
Unplugged Dryer. Opened top of Dryer, over the drum. Removed Thermal Limiter. Tested the Thermal Limiter - found it was open. Checked all vents and exhaust tube for lint build-up. Replaced Thermal Limiter. Closed top of dryer. Plugged Dryer back. Tested Dryer - it works.