This grey OEM dishwasher tub gasket is a 73" grey rubber part that creates a seal around the dishwasher to prevent any water leakage during a cycle. If it's damaged or broken, you'll start seeing wate...
The upper spray arm helps distribute water from the top of the dishwasher tub.This spray arm is a genuine OEM replacement part for your dishwasher. This spray arm is for the upper part of your dishwas...
The silverware basket, used for dishwashers, is in the bottom dishrack. The lower dishrack basket is used to hold eating utensils such as spoons, forks, and knives, and other small tools. If the baske...
The single rack roller kit comes with one axle/clip and one wheel/roller. The rack wheel is designed to allow the rack of your dishwasher to roll in and out. If the rack will not complete this task, o...
Upper Rack Assembly - T3 PRO. This is the complete upper rack and the wash arm.
$184.56
In Stock
Questions And Answers for FDB4315LFC0
Ask our experts a question about this model and we'll get back to you as soon as possible!
3 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Earnest
January 28, 2020
Have received an error code in the cycle - 'er' what triggers this code? Thanks for the help.
For model number FDB4315LFC0
Hello Earnest, thank you for your question. ER Code: Error Problem / Condition = Membrane Switch Failure
Check / Repair / Solution = Main Control Board has detected a stuck key or a key pressed for more than one minute. Check connection from keypad to Main Control Board. If correct, replace keypad. If error still exist, replace Main Control Board.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Lorenzo
November 16, 2021
Dishwasher displays pf error code about 20 to 30 minutes into wash cycle. Sometimes it works fine, sometimes it displays error. When pf error code is displayed the inside of dishwasher is extremely hot. I usually complete the wash with a rinse only cycle.
For model number FDB4315LFC0
Hello Lorenzo, thank you for your question. The PF error code stands for power failure and it appears when power has been interrupted. We recommend checking the power coming from your circuit breaker. We hope this helps.
Was this helpful?
Thank you for voting!
David
July 24, 2023
Push in washing mode and then start. close door. Time shows up on panel, IE 93 min.
This remains for about 30 seconds then the panel goes blank. It does this in all washing modes even if it is just rinse.
For model number FDB4315LFC0
Hi David, thank you for contacting us. Based on the description that you have provided, we would recommend making sure that the door closes properly and does not open during operation. Also, check the connection between the control panel and the electronic control board. If that is not causing the issue, then you may need to check the electronic control board, part number PS12365809, as it is the most likely faulty and may need to be replaced. We hope this helps!
Repair was simple. I unscrewed the old grommet which held the old spray arm and screwed-on the new one. About 30 seconds was required. Other people having this problem should note that the spray-arm is made of three pieces which are inseparable when the arm is new. The arm is sold in this form. However, when your machine is having the problem that the arm falls off, the three pieces become separate. When you want to replace the spray arm, only one new part needs to be ordered because this part encompases all three components.
First I opened the door all the way. Second I reached down to the bottom gasket then grabed it on the right end of the seal that is on the right side of the door. Then I pulled the end outward from the bottom of the door toward the heater coil in the bottom of the washer. It came out real easy. You see it just snaps into a little plastic groove under the door. I then cleaned up the area for food and soap particules. I then placed the new gasket in place by lining up the notch toward the right end with the piece of plastic that encloses the right end of the plastic notch on the bottom right end of the door. Then push it in untill it stops going into the notch. It snaps in but does not make a snaping sound. It just won't go in no more.
