FB412 (Type 0) DeVilbiss Compressor - Overview

Diagrams for FB412

See every part. Know exactly what you need.

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Strip Rubber Foot – Part Number: SUDL-6-1
No Longer Available
Strip Rubber Foot
Part #SUDL-6-1
Nut .375-16 UNC-2B H – Part Number: SSF-8080-ZN
No Longer Available
Nut .375-16 UNC-2B H
Part #SSF-8080-ZN
Sleeve Silicone – Part Number: CAC-1120
No Longer Available
Sleeve Silicone
Part #CAC-1120
Gauge Right Hand – Part Number: AC-0009-1
No Longer Available
Gauge Right Hand
Part #AC-0009-1
Head 3/8 Outlet Front – Part Number: AC-0037
No Longer Available
Head 3/8 Outlet Front
Part #AC-0037
Shroud Mini – Part Number: AC-0376
No Longer Available
Shroud Mini
Part #AC-0376
This is an authentic Porter Cable replacement part that has been sourced from the original manufacturer to be used with air compressors. The durable plastic shroud is used to house and protect the pump assembly. This item is available as an individual replacement part.
VALVE SAFETY 150 .12 – Part Number: 97503734
$16.13
Special Order
VALVE SAFETY 150 .12
Part #97503734
This safety valve is a genuine replacement part manufactured for use with air compressors. If the compressor's pressure switch malfunctions and does not turn the motor off when the amount of pressure is met, the safety valve will open to release the extra air pressure. The amount of pressure required to open the safety valve is set by the tension of the spring inside the valve. The spring can wear out, and leave the valve open at a lower pressure than what is set to turn the switch off, and will not allow pressure to build inside the tank. Please make sure to refer to the appropriate diagrams of your model for the correct location and application of this component. Keep in mind this high-quality part is made of durable metal and is sold individually.
ISOLATOR 3 POINT MOU – Part Number: ACG-19
$7.44
Special Order
ISOLATOR 3 POINT MOU
Part #ACG-19
ASSY FASTENER – Part Number: ACG-408
$7.44
Special Order
ASSY FASTENER
Part #ACG-408
This assembly fastener is supplied directly from the original equipment manufacturer. The screws are constructed of metal, and are compatible with many compressor machines. This part is often used to secure the compressor shroud. It is recommended to refer to specific manual and diagrams for repair instructions. This part is sold individually. Purchasing spare screws is also encouraged, as they can wear out over time and regular use. A hex key and a screwdriver are helpful in the removal and replacement.
ORING P/L HEAD – Part Number: ACG-45
$7.44
In Stock
ORING P/L HEAD
Part #ACG-45
O-rings are made to contain thousands of PSI pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. rnrnThere are many causes for O-Ring failure. The most common among power tools are: • Extrusion and Nibbling - The O-ring has ragged, tattered edges. These are commonly caused by pressure spikes which shear off tiny "bites" from the o-ring, or caused by clearance gaps. • Abrasion - One or both sides of the o-ring appear rough and slightly flattened. Commonly caused by a contact surface that it too rough, contains grit or is too smooth to allow lubrication. • Over Compression - The O-ring is flattened on both sides and may have a "ring" split along its length. Commonly caused by excessive pressure or heat. • Heat Hardening - The O-ring has a pitted or cracked surface, and is often flattened on both sides. Caused by temperature exceeding o-ring capacity. • Weather/Ozone Cracking - The O-ring is covered in small surface cracks. Caused by exposure to ozone, UV rays and air pollution. Excessive seal stretching (greater that 5%) causes similar cracking.
REGULATOR 4PORT P1P2 – Part Number: AC-0007
No Longer Available
REGULATOR 4PORT P1P2
Part #AC-0007
This is a genuine OEM part that is intended to be used with air compressors from Porter Cable, DeVilbiss, and Black & Decker. The regulator is used to adjust the level of pressure in the tank. This item is sold as an individual replacement part.
FILTER INTAKE – Part Number: DAC-143
No Longer Available
FILTER INTAKE
Part #DAC-143
This is an authentic OEM part. The filter is used with air compressors from Porter Cable, DeVilbiss, and Black & Decker. The foam filter is used to prevent dirt and debris from entering and potentially damaging the pump. A hex driver, or screwdriver may be needed to install this item and it is sold individually.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Can't find this special screw used on many housings etc
4 of 6 people found this instruction helpful.
  • Tim from Tucson, AZ
  • Very Easy
  • 15 - 30 mins
Actually don't like using Torx bits because they are hard to center deep in the channel. I had misplaced these forcing me to order replacements.
My plan is to insert Torx bits before screwing in and using jb weld to secure the bit to the screw, giving me a hex head. Can't find this special screw with a hex head. This screw is called AGC-408 by craftsman.
Was this helpful?
Thank you for voting!