The door strike on your washing machine allows your washer door to lock properly, and operate efficiently. If you notice that your washer door will not open or close, leaks or the washer will not star...
$19.58
In Stock
Order within the next 49 mins and your part ships today!
This door lock and switch assembly is manufactured to lock the door on your front load washer to prevent it from opening while it is running. You may need to replace the door lock and switch if the do...
$163.10
In Stock
Order within the next 49 mins and your part ships today!
Also known as a Door Boot Seal and is used in front load washers. This part is used to keep the clothes inside the tub during the wash cycle. The folds in the bellow allow the tub to move separately f...
$393.85
In Stock
Order within the next 49 mins and your part ships today!
This is a replacement screw for your washer or dryer. The screw is approximately half an inch in length and is a Phillips-head screw. It screws in from the outside of the drum, into the vane/baffle. T...
$16.47
In Stock
Order within the next 49 mins and your part ships today!
Order within the next 49 mins and your part ships today!
Questions And Answers for FAFW4011LW0
Ask our experts a question about this model and we'll get back to you as soon as possible!
5 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Barbara
September 7, 2022
Washer had a grinding noise, did not spin as the drum dropped forward and will not stay in place.
For model number FAFW4011LW0
Hello Barbara, thank you for reaching out. According to our research on the model, the problem appears to be with the Drive Belt, part number PS3490371. Customer service is available 7 days a week if you need help placing an order. We hope this helps!
The front cover on the dispenser drawer came off, looks like a clip broke off. What do I need to buy, is the drawer and cover separate?
For model number FAFW4011LW0
Hello Brian, thank you for writing. We suggest checking the Dispenser Drawer Handle Frame for wear or damaged. This part holds the handle (cover) to the Drawer. We hope this helps!
Water is not entering for washing - I've tried resetting that didn't work & different settings what possibilities could be wrong. Thank you
For model number FAFW4011LW0
Hi Cheryl, thank you for reaching out. Based on our understanding of the issue, we would suggest that you check the water inlet valve, part number PS3490374, as it is most likely faulty and may need to be replaced. We hope this helps!
SO ....... for a total change out of ALL the shock absorbers on the model..........do I need a total of TWO individual shock absorbers or a total of FOUR?
For model number FAFW4011LW0
Hello Todd, thank you for contacting us. Upon reviewing the model provided, the shock absorbers are available in a set of two, Rear Shock Absorbers, part number PS8689635, and Front Shock Absorbers, part number PS8689636. Four are required on the unit. Good luck with your repair! If you need help placing an order, customer service is open 7 days a week. Thanks again for your great question.
This was one of the simpliest repairs I have ever done taking less than 5 minutes to complete. On the inner door I removed the two screws that hold the plastic catch in place. I then removed the broken catch and put the new catch in place. Finally I replaced the two screws that hold the catch in place and it was done.
1. Unplug unit. 2. Unscrew 2 nuts holding top in place in rear of unit using phillips head screwdriver. 3.Slide top back and remove. 4. Open door of washer and unscrew 2 screws holding in door lock unit. 5.Pull out unit from the top and install new unit reconnecting the 3 wire connections.
remove top of machine by removing 3 screws along the top edge in the back of your machine and then sliding the top back and up. Then loosen the screws holding on the control panel enough to get to the 2 screws at the top of the door panel. Next remove bottom panel by removing 2 screws along bottom edge then pulling it free from snaps. Then along the outside lip of the bellow, just inside the door, is a wire clip that is easily removed by prying it past rubber lip with a screw driver and lifting it away. Remove the door panel by removing the 2 screws you exposed by loosening the control panel and 2 more along the bottom that were exposed when removing bottom panel. After the door panel is removed and the bellow is completely exposed, you will find that it is held in place by a circular spring which wraps the whole way around the drum opening. Again it can be removed by prying it out away from the groove in which it sits with a screw driver. Now your machine is broken down as far as it needs to be. From here you can follow the directions included in your new bellow kit and put it back together by following these instructions in reverse.
