EXFA2030SV (Type 0) DeVilbiss Compressor - Overview

O-rings are made to contain thousands of PSI pressure by creating a seal between two or more parts. O-ring measurements are defined by the inside diameter and the thickness. rnrnThere are many causes for O-Ring failure. The most common among power tools are: • Extrusion and Nibbling - The O-ring has ragged, tattered edges. ...Read moreThese are commonly caused by pressure spikes which shear off tiny "bites" from the o-ring, or caused by clearance gaps. • Abrasion - One or both sides of the o-ring appear rough and slightly flattened. Commonly caused by a contact surface that it too rough, contains grit or is too smooth to allow lubrication. • Over Compression - The O-ring is flattened on both sides and may have a "ring" split along its length. Commonly caused by excessive pressure or heat. • Heat Hardening - The O-ring has a pitted or cracked surface, and is often flattened on both sides. Caused by temperature exceeding o-ring capacity. • Weather/Ozone Cracking - The O-ring is covered in small surface cracks. Caused by exposure to ozone, UV rays and air pollution. Excessive seal stretching (greater that 5%) causes similar cracking.

Genuine Porter Cable replacement part Includes 2 Carbon Brushes with wire lead attached and installation instructions. • Worn brushes are frequently the cause of a poorly running motor. • Replacing brushes can fix an intermittently operating motor. • New brushes can restore a motor's electric braking. Carbon motor brushes are...Read more one of the most commonly replaced power tool parts. The reason is that carbon brushes are wear items, meaning that through friction and use they will gradually wear away and eventually will need replacing. Worn brushes are a common causes of intermittent motor function, reduced electric braking and reduced motor power. A worn-out brush will often be worn down near to the wire lead and can be cracked, pitted, or burned. When replacing carbon brushes, also check your armature for burns, cracks, or other damage which are indications of a larger motor problem needing attention.

This safety valve is a genuine replacement part manufactured for use with air compressors. If the compressor's pressure switch malfunctions, and does not turn the motor off when the amount of pressure is met, the safety valve will open to release the extra air pressure. The amount of pressure required to open the safety valve is set by te...Read morension of the spring inside the valve. The spring can wear out, and leave the valve open at a lower pressure than what is set to turn the switch off, and will not allow pressure to build inside the tank. This safety valve has a thread sealant pre-applied, so additional thread sealant is not required, the safety valve is sold individually.

This is an OEM part sourced directly from the manufacturer. The belt is commonly found in Craftsman air compressors. This part is made of flexible rubber, and is used to transfer power between the piston and the pump assembly. Over time, it may become cracked and brittle, requiring replacement. You may need an Allen wrench or hex key when replacing this part. This item is sold individually.

This is an OEM part sourced directly from the manufacturer. The adapter is designed for use in compressors from DeVilbiss, Black & Decker, Delta, and Porter Cable. This part is made of metal, and may be used to connect the regulator to the tank. You will require a wrench when replacing this part. This item is sold individually.

This replacement hose clamp is designed for use in various compressor models and serves an important role in securing hoses to specific parts of the unit. Whether you're performing maintenance or replacing worn components, this clamp helps ensure a tight, leak-free connection. Made from durable metal and sold individually, it’s easy to in...Read morestall and built to withstand the pressure and vibration common in compressor operation. If your hose feels loose or you're noticing air leaks, replacing the clamp can help restore proper function and keep your compressor running smoothly.

This is an original Porter Cable replacement part manufactured for use with air compressors. The rubber isolator is used to reduce vibration caused by the pump and motor. This isolator is sold individually.

This is an authentic item that is supplied directly from the original equipment manufacturer for use with air compressors. It is an identical replacement for damaged or missing cylinder head that was installed on a new unit, please make sure to refer to the appropriate diagrams of your model for the correct application of this component. ...Read moreThis high-quality part is made of durable metal with plastic and is sold individually, keep in mind the gasket and the hardware are all sold separately.

This is a genuine replacement part sourced directly from the manufacturer. The screw is commonly found in compressors and generators from Porter Cable, Delta, DeWALT, DeVilbiss, and Black & Decker. This part is made of metal, and may be found in various locations in the machine, depending on model. Please be aware that there are differ...Read moreent screws used in the machine. Refer to the parts diagram to be sure of ordering the correct part. You will require a screwdriver when replacing this product. This item is sold as an individual replacement part.