The rack track stop on your dishwasher is designed to stop the dish rack at the appropriate place when opening and closing the rack. If your dishwasher is not cleaning your dishes properly, the rack s...
$9.83
In Stock
Order within the next 5 hrs and your part ships today!
This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
$10.21
In Stock
Order within the next 5 hrs and your part ships today!
This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of wat...
$73.11
In Stock
Order within the next 5 hrs and your part ships today!
The lid hinge pin or detergent lid pin on your dishwasher helps dispense your dish detergent when your dishwasher is running. The pin fits with the dispenser lid and allows the lid to pop open and dis...
$16.59
In Stock
Order within the next 5 hrs and your part ships today!
This part covers your soap dispenser and is spring loaded.
$34.87
In Stock
Order within the next 5 hrs and your part ships today!
Questions And Answers for DU850SWLQ0
Ask our experts a question about this model and we'll get back to you as soon as possible!
1 question answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Wally
September 18, 2021
The detergent door will not open fully when the door is closed. It hits the lower dishrack that prevents it from opening. Does sit need alignment?
For model number DU850SWLQ0
Hello Wally, thank you for writing. Is it possible that the lower dishrack was replaced with the incorrect one? And, are you sure it it actually touching the lower rack? If not, it may be a latch issue. Lower Detergent Dispenser Actuator Assembly PartSelect Number PS392727, The Lower Rack is PartSelect Number PS1964469. Good luck with your repair.
Installed new door seal. Dishwasher still leaked. Googled the model number and then cleaned the filter at the bottom of the dishwasher, still leaked. Verified that manifold bearing was not work. It was OK. Found note that a plugged vent might cause leaking door. Very counterintuitive. Pried off air vent cover. Vent was thouroughly plugged with calcium deposts from steam. Cleaned these out. Dishwasher no longer leaks.
Photograph or diagram how the wires connect to the switches before taking out the old assembly. I could have salvaged switches from the old assembly by pulling out the white pins (and avoided buying the new switch kit). There's only one way the pieces go back together, so the wire connections are the only point that required special care and attention.
The first thing I did was to investigate. I needed to find where the leak was coming from. It was leaking from just above tne door front panel, directly underneath the control panel buttons. I opened the dishwasher door, and decided to remove the door screen vent. I was covered with some offwhite fiberous, or filter like material. I thought perhaps the filter had broken down, and I ordered a new screen. When it arrived, and, although I had expected to receive a new filter with the plastic door screen, I didn't. There wasn't one to be ordered. I looked at the screen again. My problem was, that although I had considered that the substance I had thought was a filter, was instead build up of detergent, and other particals. That idea didn't seem to make sense. I didn't think it was possible for that stuff to get to the door screen. I thought, it was too far away from the dispenser and food particles. As it turned out, the buildup was, in fact, the problem. I properly cleaned the door vent, which was then fine, and I put it back into the door. There were no more leaks, that was it, and the problem was solved. As a last note however, unfortunatley, I have to return the new door vent screen that I ordered. I enjoyed solving the problem, and you all helped alot. Let's do it again sometime.